BYD
Chery
Great Wall / Haval
Geely
MG
Volkswagen Touareg Inner High-Beam Projector Retrofit
A source-based reference for adding projectors at the inner high-beam positions while retaining the photographed factory lighting components and shroud mounting points.
2019–2021 Touareg HeadlampInner High-Beam Projector Bracket Application
The supplied reference identifies a dedicated bracket system for the inner high-beam locations of the pictured Touareg headlamp, with a slim-projector requirement and factory-shroud mounting.
- Model
- Volkswagen Touareg
- Years
- 2019–2021 reference range
- Position
- Inner high-beam location
- Sealant
- Factory Hella cold sealant
- Harness
- H4 wide-voltage harness shown
- Projector
- Slim body recommended
The bracket fastens at the three photographed factory-shroud points.
Keep the cornering-light source inside the headlamp for final reassembly.
Set low-beam height first, then align high beams to that reference.
Wiring, Clearance and Factory Mounting Controls
Four Signal Connections
Identify the positive and negative high-beam and low-beam signals before connecting the H4 wide-voltage harness.
Slim Projector Required
The inner location has restricted clearance; confirm body size and prepare the indicated outer corner only.
Three-Point Factory Mount
Install the bracket and projector assembly onto the factory shroud at the three photographed mounting points.
Verify the Exact Touareg Headlamp before Ordering
Reference Applies To
- 2019–2021 Touareg configuration shown
- Inner high-beam projector position
- Factory Hella cold-sealed housing
- H4 wide-voltage wiring arrangement
- Slim projector and three-point shroud mount
Not Automatically Confirmed
- Other model years or headlamp suppliers
- Outer projector position
- No-opening installation methods
- Full-size projector bodies
- Unverified vehicle-side signal polarity
Send Photos for Verification
Provide the model year, headlamp face, label, internal layout, connector and intended projector dimensions.
Touareg Inner High-Beam Installation Sequence
Open the Lens and Remove the DRL
Open the factory Hella cold-sealed lens cover and remove the daytime-running-light assembly for access.
Remove the Inner Trim Panel
Remove the inner trim panel carefully and retain all reusable mounting hardware.
Remove the Cornering-Light Module
Remove the factory cornering-light module while keeping its light source inside the headlamp for final reassembly.
Prepare the Slim Projector
Use a slim projector and cut only the marked outer corner to obtain the required clearance.
Install the Lower Adjustment Screw
Pass the screw through the lower mounting hole, tighten the nut and add silicone tubing if later height adjustment is required.
Mount and Align the Projectors
Fix the assembly to the factory shroud at three points, align both low beams first and then set the high beams to the low-beam reference level.
Detailed Installation Gallery
Match the Brackets, Harness, Projectors and Hardware
Inner High-Beam Bracket Set
Confirm the dedicated left/right 2019–2021 Touareg inner-position bracket assemblies.
H4 Wide-Voltage Harness
Match and verify all four high/low-beam positive and negative signal connections before operation.
Slim Projector Pair
Use compact projector bodies that clear the inner trim and factory shroud after the indicated corner preparation.
Guide and Adjustment Hardware
Confirm the plastic guide pins, lower screws, nuts and optional silicone adjustment sleeves shown in the reference.
Inner High-Beam Projectors Installed and Aligned
The completed reference restores the daytime-running-light assembly and retained cornering-light source after bracket installation and staged beam alignment.
- Correct 2019–2021 lamp confirmed
- H4 signal polarity verified
- Slim projector clearance checked
- Three factory-shroud points secured
- Low beams aligned before high beams
Touareg Inner High-Beam Projector Retrofit FAQ
Which projector position is covered?
The supplied reference covers the inner high-beam position of the pictured 2019–2021 Volkswagen Touareg headlamp.
Does the front lens cover need to be opened?
Yes. The pictured lamp uses factory Hella cold sealant; the lens cover and daytime-running-light assembly are removed for access.
Which wiring harness is shown?
The reference identifies an H4 wide-voltage harness and four vehicle-side signal lines. Verify high-beam positive and negative plus low-beam positive and negative before connection.
What happens to the cornering-light module?
Remove the factory cornering-light module, but keep its light source inside the headlamp for final reassembly as shown.
Which projector body is recommended?
A slim projector is recommended because the inner high-beam position has limited clearance. Confirm body dimensions before ordering.
How should the beam heights be aligned?
First align the left and right low-beam projector heights. Then use the low-beam level as the reference when adjusting the high-beam projectors.
Technical reference: Based on Royalin-supplied installation photography and article 357 for the pictured 2019–2021 Volkswagen Touareg inner high-beam projector configuration. Verify the headlamp supplier, sealant, connector signals, projector dimensions, mounting points and retained light source before ordering.
Related Headlight Retrofit Cases
Need This Touareg Inner High-Beam Bracket?
Send the model year, headlamp label, connector, internal layout and slim-projector dimensions for matching.
Professional lens opening, wiring verification, bracket installation, beam alignment and resealing are recommended.