BYD
Chery
Great Wall / Haval
Geely
MG
Volkswagen Tiguan L PRO Inner High-Beam Projector Retrofit
A source-based reference for converting the inner high-beam position of the pictured mid/low-trim headlamp while retaining the OEM light source and using the specified non-common-negative wide-voltage harness.
Inner High-Beam Hella SolutionIndependent Inner High-Beam Conversion
This case is the inner high-beam Hella-pattern option. It differs from the inner matrix and outer 3-inch projector solutions available for the same headlamp family.
- Model
- Volkswagen Tiguan L PRO
- Year
- 2026 reference
- Headlamp
- Mid/low-trim unit shown
- Position
- Inner high beam
- Projector
- 3-inch square body only
- Wiring
- Non-common-negative wide-voltage harness
Keep the original light source in the system as specified.
The original plated decorative shroud must be removed and the appearance change is visible.
Match a 3-inch square projector to the Hella-pattern bracket.
Bracket Orientation and Circuit Identification
Bracket Orientation
Flip down the marked fitting before installation and keep the left/right parts matched to the pictured orientation.
Vehicle-Side Signals
Identify the low- and high-beam positive and negative circuits before adding the required harness.
Harness-Side Signals
Use the non-common-negative wide-voltage harness and verify polarity before powering the projector.
Confirm the Exact Inner-Position Solution
Reference Applies To
- 2026 Tiguan L PRO configuration shown
- Mid/low-trim headlamp
- Independent inner high-beam conversion
- Hella-pattern bracket
- 3-inch square projector
Not Automatically Confirmed
- Inner matrix-projector bracket
- Outer-position 3-inch bracket
- Round or differently shaped projectors
- Installation with the plated shroud retained
- Common-negative or unverified wiring
Send Photos for Verification
Provide the model year, full headlamp front, label, rear housing, inner carrier and driver connector.
Inner High-Beam Hella Bracket Installation Sequence
Open the Valeo Cold-Sealed Headlamp
Open the factory Valeo cold-sealed lens cover using controlled heat and approved headlamp-opening procedures.
Remove the DRL Assembly
Remove the marked retaining screws, then lift out the DRL assembly without damaging the optical surfaces.
Remove the Factory Projectors
Remove the original projector assemblies and keep the reusable hardware, light source and wiring organized.
Install the Hella-Pattern Bracket
Fit the inner-position bracket, connect the linkage rod where required and verify all mounting points.
Pre-Fit the Square Projector
Install the 3-inch square projector from the front and trim only the marked corner if it interferes with the factory shroud area.
Restore and Test the Headlamp
Remove the original plated shroud as required, restore the trim, test both beam circuits and reseal the housing.
Detailed Installation Gallery
Match the Bracket, Projector, Source and Harness
Inner High-Beam Bracket Set
Confirm the dedicated left/right Hella-pattern brackets, clips, posts and fasteners.
3-Inch Square Projector
This reference supports a 3-inch square projector; verify body depth and front clearance.
OEM Light Source
Retain the original vehicle light source exactly as specified by the source reference.
Wide-Voltage Harness
Use the non-common-negative wide-voltage harness and confirm circuit polarity before operation.
Inner High-Beam Projector Installed
The completed reference shows the inner position restored after fitting the Hella-pattern bracket and 3-inch square projector.
- Correct mid/low-trim lamp confirmed
- OEM light source retained
- Original plated shroud removed
- Non-common-negative harness connected
- Beam operation, alignment and sealing verified
Tiguan L PRO Inner High-Beam Retrofit FAQ
Which headlamp position does this bracket convert?
This case converts the inner high-beam position of the pictured 2026 Tiguan L PRO mid/low-trim headlamp. It is separate from the outer-position and inner-matrix solutions.
Which projector shape and size fits this bracket?
The supplied reference specifies a 3-inch square projector with a Hella-pattern mounting interface. Other body shapes are not automatically confirmed.
Must the factory plated shroud be removed?
Yes. The original plated decorative shroud must be removed for this installation, and the change is visible from outside the headlamp.
Can the original vehicle light source be retained?
Yes. The reference requires retaining the original light source while adding the projector system.
What wiring harness is required?
Use the specified non-common-negative wide-voltage harness. Confirm the positive and negative low- and high-beam signals before connection.
Can only the inner high-beam position be converted?
Yes. The source states that the inner high-beam position can be converted independently, provided projector clearance, wiring and final beam performance are verified.
Technical reference: Based on Royalin-supplied installation photography and article 1467 for the pictured 2026 Volkswagen Tiguan L PRO mid/low-trim headlamp. Verify the inner position, square-projector dimensions, shroud removal, retained source and non-common-negative wiring before ordering.
Related Headlight Retrofit Cases
Need This Inner High-Beam Hella Bracket Solution?
Send the model year, headlamp appearance, label, inner carrier and projector specifications for matching.
Professional lamp opening, wiring verification, projector alignment, trim checks and resealing are recommended.