BYD
Chery
Great Wall / Haval
Geely
MG
Volkswagen Tiguan L / Allspace 25W Projector Retrofit
A source-based rear-access reference for the pictured Tiguan Allspace 25W headlamp, covering rivet and internal-support cutting, reflector and factory-carrier removal, shroud transfer, and replacement bracket installation while the clear front lens remains installed.
Tiguan Allspace 25W HeadlampTiguan Allspace 25W Rear-Access Bracket Application
The clear outer lens is retained. The reflector, motor clip, lower ball-joint support and factory projector carrier are removed through the rear opening using the source-specified sequence.
- Model
- Volkswagen Tiguan L / Allspace
- Years
- 2017–2019 reference
- Headlamp
- OEM 25W unit shown
- Access
- Rear housing; lens retained
- Bracket
- Vehicle-specific metal set
Match the pictured headlamp and carrier layout.
18-inch bolt cutters and angled sheet-metal snips are shown.
Transfer the factory small black shroud and reinforce it with Kafuter 5905 silicone.
Prepare the Tools and Bracket Before Removal
Use the Specified Tools
The source shows 18-inch bolt cutters and angled sheet-metal snips for controlled rear-access removal.
Open the Factory Rivet First
Cut the rivet before removing the reflector bowl and keep cut fragments out of the housing.
Release the Factory Carrier
Release the motor clip, lower ball-joint support and marked fastener before withdrawing the factory carrier.
Confirm the 25W Headlamp Before Cutting
Reference Applies To
- 2017–2019 Tiguan Allspace 25W headlamp shown
- Matching vehicle-specific bracket set
- Rear-access reflector and carrier removal
- Compatible projector body
- Factory small black shroud retained
Not Automatically Confirmed
- Other wattage or adaptive headlamps
- Different rear openings or carrier layouts
- Cutting outside the marked mounting points
- Unverified projector or factory-shroud dimensions
- Installation without final beam aiming
Send Photos for Verification
Provide the year, headlamp label, rear opening, factory carrier and projector measurements.
Tiguan Allspace 25W Rear-Access Installation Sequence
Cut the Factory Rivet
Use the 18-inch bolt cutters to open the factory rivet through the rear access opening.
Remove the Reflector Bowl
Cut only the marked supports and carefully withdraw the reflector bowl without scratching internal parts.
Release the Motor Retaining Clip
Release the motor retaining clip; remove the motor as needed to provide safe working clearance.
Cut the Lower Ball-Joint Support
Cut the lower inner ball-joint support and release the factory bracket clip at the marked location.
Free the Factory Projector Assembly
Remove the marked fastener and withdraw the original projector and plastic bracket assembly.
Install the New Bracket and Projector
Seat the metal bracket, warm and adjust tight clips only if needed, then install and align the projector.
Detailed Installation Gallery
Match the Bracket, Projector, Shroud and Tools
Tiguan Allspace 25W Bracket Set
Confirm the dedicated left/right metal brackets, retaining clips, posts and supplied fasteners.
Compatible Projector
Match the projector body and mounting pattern to the vehicle-specific bracket before insertion.
Factory Small Black Shroud
Transfer the original small black shroud directly to the projector and reinforce it with Kafuter 5905 silicone.
Specified Cutting Tools
Use the 18-inch bolt cutters and angled sheet-metal snips only at the marked supports and fasteners.
Projector Installed with the Clear Front Lens Retained
The completed reference shows the replacement projector aligned behind the original exterior lens after rear-access bracket installation.
- Correct 25W headlamp confirmed
- Factory rivets and carrier removed in sequence
- Vehicle-specific bracket seated on retained points
- Factory small black shroud transferred and projector tightened
- Beam operation, aim and rear closure require final inspection
Tiguan Allspace 25W Rear-Access Retrofit FAQ
What does no-lens-opening mean for this Tiguan Allspace retrofit?
The clear front lens remains installed. The factory reflector and projector carrier are removed through the rear access opening shown in the source.
Which headlamp does this bracket fit?
This reference is for the pictured 2017–2019 Volkswagen Tiguan L / Allspace 25W headlamp. Confirm the lamp label and carrier layout before ordering.
Which tools are shown?
The source specifies 18-inch bolt cutters and angled sheet-metal snips for the rear-access removal sequence.
Which original components are removed?
The reflector bowl, motor retaining clip, lower inner ball-joint support, marked fastener and factory plastic projector bracket are removed as shown.
Is the factory small black shroud retained?
Yes. Attach the factory small black shroud directly to the replacement projector and reinforce it with Kafuter 5905 silicone as shown.
What must be checked after installation?
Verify clip engagement, bracket seating, projector clearance, beam operation and aim before completing the rear closure.
Technical reference: Based on Royalin-supplied installation photography and article 58 for the pictured 2017–2019 Volkswagen Tiguan L / Allspace 25W headlamp. Verify wattage, housing, carrier, projector dimensions and mounting points before ordering.
Related Headlight Retrofit Cases
Need This Tiguan Allspace 25W Retrofit Solution?
Send the year, headlamp label, rear-housing photos and projector measurements for matching.
Professional controlled cutting, debris protection, projector alignment and beam aiming are recommended.