01 Hero · non-adaptive projector case

2021–2024

Volkswagen ID.4 CROZZ Non-Adaptive Projector Retrofit

Factory-Ring Vehicle-Specific Bracket
INSTALLATION REFERENCE

A source-based reference for replacing the projector in the pictured non-adaptive Xingyu headlamp while retaining its factory plastic ring and exterior trim architecture.

◇ Volkswagen ID.4 CROZZ◇ 2021–2024◇ Non-Adaptive Headlamp◇ Factory Retaining Ring Reused

View Installation Guide

2021 to 2024 Volkswagen ID.4 CROZZ headlampID.4 CROZZ Non-Adaptive Headlamp
02 Vehicle-specific application

Non-Adaptive Projector Bracket Application

The supplied bracket pair mounts a replacement projector in the pictured non-adaptive ID.4 CROZZ headlamp and reuses the original plastic retaining ring and outer trim pieces.

Model
Volkswagen ID.4 CROZZ
Years
2021–2024 reference range
Headlamp
Non-adaptive unit shown
Supplier
Xingyu cold-sealed housing
Projector
Square body recommended
Ring
Factory plastic ring retained
2021 to 2024 Volkswagen ID.4 CROZZ non-adaptive projector bracket kit
Non-Adaptive Only

Do not use this bracket for motorized or adaptive projector assemblies.

Verified Pin Mapping

Confirm low/high-beam polarity at the identified connector pins.

Controlled Shroud Preparation

Trim and enlarge only the photographed areas required for final fitment.

03 Technical reference

Connector Pins, Retaining Ring and Shroud Clearance

Volkswagen ID.4 CROZZ low and high beam connector pin reference

Verify Beam Polarity

Low beam uses pins 4 negative and 5 positive; high beam uses pins 1 negative and 2 positive in the photographed connector.

Volkswagen ID.4 CROZZ factory retaining ring transfer

Reuse the Factory Ring

Transfer the original plastic retaining ring to the new bracket and confirm it seats fully before projector installation.

Volkswagen ID.4 CROZZ factory shroud hole enlargement

Prepare the Factory Shroud

Enlarge only the photographed shroud holes from approximately 3 mm to 4 mm and maintain correct trim alignment.

04 Compatibility notice

Verify the Non-Adaptive Xingyu Headlamp

Reference Applies To

  • 2021–2024 Volkswagen ID.4 CROZZ configuration shown
  • Non-adaptive projector headlamp
  • Factory Xingyu cold-sealed housing
  • Original plastic retaining ring
  • Compatible square projector body

Not Automatically Confirmed

  • Adaptive or motorized headlamps
  • Other ID.4 regional headlamp versions
  • No-opening installation methods
  • Round or oversized projectors without clearance checks
  • Unverified connector polarity

Send Photos for Verification

Provide the model year, headlamp label, front signature, connector, retaining ring and projector dimensions.

Request Verification

05 Installation process

ID.4 CROZZ Non-Adaptive Installation Sequence

Open the Xingyu Cold-Sealed Headlamp

Step 01

Open the Xingyu Cold-Sealed Headlamp

Open the factory Xingyu cold-sealed front cover using controlled headlamp-opening procedures.

Release the Upper Trim Cover

Step 02

Release the Upper Trim Cover

Pry up the upper trim cover carefully, then remove the photographed upper and lower fasteners.

Remove the Factory Projector Shroud

Step 03

Remove the Factory Projector Shroud

Remove the original shroud and retain the plastic ring and trim pieces required for reassembly.

Transfer the Factory Retaining Ring

Step 04

Transfer the Factory Retaining Ring

Install the original plastic retaining ring onto the new non-adaptive bracket and confirm secure engagement.

Install the Bracket to the Rear Housing

Step 05

Install the Bracket to the Rear Housing

Mount the bracket and recommended square projector onto the rear housing and verify wiring clearance.

Restore the Shroud and Trim Panel

Step 06

Restore the Shroud and Trim Panel

Trim the shroud only where required, enlarge the three-millimetre holes to four millimetres and reinstall the outer trim panel.

Detailed Installation Gallery

06 Components to confirm

Match the Brackets, Projectors, Factory Rings and Hardware

Non-Adaptive Bracket Pair

Confirm the dedicated left/right ID.4 CROZZ non-adaptive bracket assemblies and mounting direction.

Square Projector Pair

Use projector bodies compatible with the factory shroud opening and rear-housing clearance.

Factory Retaining Rings

Transfer and securely seat the original plastic retaining rings on the new brackets.

Fasteners and Wiring Hardware

Confirm the clips, screws, nuts, connectors and polarity references before opening the lamps.

Completed Volkswagen ID.4 CROZZ non-adaptive projector retrofit
07 Installation result

Non-Adaptive Projector and Factory Trim Restored

The completed reference restores the original trim panel around the replacement projector and vehicle-specific bracket.

  • Correct non-adaptive Xingyu lamp confirmed
  • Factory plastic retaining ring reused
  • Square projector clearance verified
  • Shroud holes prepared to the specified size
  • Beam polarity, aim and sealing tested
08 Frequently asked questions

Volkswagen ID.4 CROZZ Non-Adaptive Retrofit FAQ

Which ID.4 CROZZ headlamp is covered?

The supplied reference covers the pictured 2021–2024 Volkswagen ID.4 CROZZ non-adaptive headlamp. Confirm the lamp label and internal mounting layout before ordering.

Is this bracket for an adaptive headlamp?

No. This page covers the non-adaptive configuration shown. High-spec adaptive or motorized lamps require a different bracket and verification.

Which wiring pins are identified?

The reference identifies low-beam pin 4 as negative and pin 5 as positive; high-beam pin 1 as negative and pin 2 as positive. Verify on the vehicle before connection.

Which projector shape is recommended?

A square projector is recommended because it better matches the available factory shroud opening and reduces clearance work.

Can the factory plastic retaining ring be reused?

Yes. Transfer the pictured factory plastic retaining ring to the new bracket and confirm it locks securely before installing the projector.

What shroud preparation is required?

Trim the upper and lower shroud areas only as needed, then enlarge the photographed factory shroud holes from approximately 3 mm to 4 mm for final fitment.

Technical reference: Based on Royalin-supplied installation photography and article 850 for the pictured 2021–2024 Volkswagen ID.4 CROZZ non-adaptive projector bracket. Verify the headlamp supplier, connector pins, retaining ring, projector dimensions, shroud clearance and sealant before ordering.

Related Headlight Retrofit Cases

09 Business inquiry

Need This ID.4 CROZZ Non-Adaptive Bracket?

Send the vehicle year, headlamp label, connector, retaining-ring photos and projector dimensions for matching.

Professional lens opening, wiring verification, controlled shroud preparation, beam alignment and resealing are recommended.

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.