BYD
Chery
Geely
MGVolkswagen ID.3 Mid/Low-Spec Inner High-Beam Retrofit
A source-based reference for adding a projector only at the pictured inner high-beam position while retaining the remaining factory optical layout.
High-Beam Position Retrofit OnlyInner High-Beam Projector Bracket Application
The supplied reference identifies a dedicated left/right bracket pair for the inner high-beam position of the pictured mid/low-spec ID.3 headlamp.
- Model
- Volkswagen ID.3
- Years
- 2021–2025 confirmed reference
- Headlamp
- Mid/low-spec unit shown
- Position
- Inner high-beam only
- Sealant
- Factory Valeo cold sealant
- Adjustment
- Independent height access
The photographed conversion leaves the remaining factory optical system in place.
Match the projector control to the verified 8.7V high-beam signal.
Modify only the specific bowl and trim areas that interfere with the projector.
Signal Input, Reflector Clearance and Independent Adjustment
Verify the 8.7V High-Beam Signal
Use a compatible wide-voltage input and confirm the positive/negative high-beam wires before connection.
Preserve Unmarked Reflector Areas
Remove only the marked support and flange sections needed for bracket and projector clearance.
Keep the Adjustment Port Accessible
The final access opening permits independent height adjustment of the installed 3-inch projector.
Verify the Mid/Low-Spec ID.3 Headlamp
Reference Applies To
- 2021–2025 Volkswagen ID.3 configuration shown
- Mid/low-spec reflector-based headlamp
- Inner high-beam position only
- Factory Valeo cold-sealed housing
- Matching projector body and bracket geometry
Not Automatically Confirmed
- 2026 model without physical verification
- High-spec adaptive headlamps
- Low-beam or full multi-projector conversion
- No-opening installation methods
- Unverified signal voltage or polarity
Send Photos for Verification
Provide the model year, headlamp face, label, reflector layout, connectors and intended projector dimensions.
ID.3 Inner High-Beam Installation Sequence
Open the Valeo Cold-Sealed Front Cover
Open the factory Valeo cold-sealed lens cover using controlled headlamp-opening procedures.
Remove the High-Beam Reflector Assembly
Remove the factory high-beam bracket and reflector bowl to expose the inner mounting position.
Prepare the Reflector Bowl and Bracket Area
Cut only the indicated rear clearance area, remove the marked reflector support and trim the required bowl flange.
Prepare the Projector Clearance
Trim the lower outer edge of the projector or, when preferred, cut only the interfering reflector-bowl area.
Install the Projector Bracket Assembly
Fit the vehicle-specific bracket and projector into the inner high-beam position and secure all mounting points.
Restore Trim Clearance and Adjustment Access
Locally trim the innermost wing panel and upper black trim where required, then confirm the independent height-adjustment opening remains accessible.
Detailed Installation Gallery
Match the Brackets, Projectors, Signal Interface and Hardware
Inner High-Beam Bracket Pair
Confirm the dedicated left/right ID.3 mid/low-spec inner-position bracket assemblies.
Compatible 3-Inch Projectors
Match projector body dimensions to the photographed bracket and available reflector-bowl clearance.
Wide-Voltage Signal Interface
Use a verified wide-voltage input compatible with the photographed high-beam positive and negative signal.
Clips, Spacers and Fasteners
Confirm the supplied clips, white spacers, screws, nuts and all mounting hardware before opening the lamps.
Inner High-Beam Projector Installed
The completed reference restores the headlamp around the added inner high-beam projector while retaining adjustment access.
- Correct mid/low-spec headlamp confirmed
- Inner high-beam position bracket secured
- Wide-voltage input verified
- Only marked reflector and trim areas modified
- Projector aim, beam function and sealing tested
Volkswagen ID.3 Inner High-Beam Retrofit FAQ
Which ID.3 headlamp is covered?
The supplied reference covers the pictured 2021–2025 Volkswagen ID.3 mid/low-spec headlamp and modifies only the inner high-beam position.
Is the 2026 model confirmed?
The folder name includes 2026, but the supplied technical image identifies 2021–2025. A 2026 headlamp requires label, connector and internal-layout verification before ordering.
Does the headlamp need to be opened?
Yes. The pictured unit uses factory Valeo cold sealant; open the front cover and remove the factory high-beam reflector assembly.
What wiring input is required?
The photographed high-beam positive and negative signal is approximately 8.7 volts and requires a compatible wide-voltage input. Verify polarity and live voltage before connection.
Where is trimming required?
Trim only the photographed reflector-bowl flange, projector lower outer edge or bowl clearance area, upper black trim panel and innermost wing panel as required by the chosen projector.
Can the projector height be adjusted independently?
Yes. The final reference shows an access opening that allows independent height adjustment of the installed 3-inch projector.
Technical reference: Based on Royalin-supplied installation photography and article 888 for the pictured 2021–2025 Volkswagen ID.3 mid/low-spec inner high-beam projector bracket. Verify the headlamp specification, Valeo sealant, high-beam signal, projector dimensions, reflector clearance and adjustment access before ordering.
Related Headlight Retrofit Cases
Need This ID.3 Inner High-Beam Bracket?
Send the vehicle year, headlamp label, connector, internal layout and intended projector dimensions for matching.
Professional lens opening, voltage verification, controlled reflector trimming, beam alignment and resealing are recommended.
