BYD
Chery
Geely
MGVolkswagen ID.3 Mid/Low-Spec 3-Inch + Matrix Retrofit
A source-based reference for upgrading the pictured ID.3 headlamp with a primary 3-inch projector and compact matrix projectors on one vehicle-specific bracket system.
ID.3 Mid/Low-Spec HeadlampIntegrated 3-Inch and Compact Matrix Architecture
The supplied kit combines direct 3-inch projector mounting, universal 1.5–1.8-inch matrix projectors and model-specific outer trim panels for the pictured mid/low-spec ID.3 headlamp.
- Model
- Volkswagen ID.3
- Years
- 2021–2023 reference range
- Headlamp
- Mid/low-spec unit shown
- Primary
- 3-inch projector position
- Matrix
- Universal 1.5–1.8-inch units
- Sealant
- Factory Valeo cold sealant
Mount the primary and compact projectors on the same vehicle-specific carrier.
Use a compatible wide-voltage input for the photographed high-beam signal.
Cut only the marked trim-panel area above the 3-inch projector.
Beam Signals, Projector Layout and Trim Clearance
Low-Beam Signal Check
Verify the low-beam positive and negative wires at the vehicle before connecting the retrofit system.
Wide-Voltage High-Beam Input
The photographed high-beam control requires a compatible wide-voltage input; verify polarity and voltage before operation.
Optional Factory Light-Source Layout
If retaining the original light source, follow the photographed placement and confirm clearance against all projectors and wiring.
Verify the Mid/Low-Spec ID.3 Headlamp
Reference Applies To
- 2021–2023 Volkswagen ID.3 configuration shown
- Mid/low-spec reflector-based headlamp
- Factory Valeo cold-sealed housing
- 3-inch plus 1.5–1.8-inch matrix layout
- Matching bracket and trim-panel set
Not Automatically Confirmed
- 2024–2026 vehicles without physical verification
- High-spec adaptive headlamps
- No-opening installation methods
- Other projector body dimensions
- Unverified signal voltage or polarity
Send Photos for Verification
Provide the model year, headlamp face, label, reflector layout, connectors and intended projector specifications.
ID.3 3-Inch + Matrix Installation Sequence
Open the Valeo Cold-Sealed Headlamp
Open the factory Valeo cold-sealed lens cover using controlled headlamp-opening procedures.
Remove the Factory Reflector Bowl
Remove the reflector-bowl assembly to expose the rear housing and original mounting structure.
Assemble the Matrix Projectors
Install the universal 1.5–1.8-inch matrix projectors and supplied clips onto the vehicle-specific bracket.
Mount the Bracket to the Housing
Position and fasten the completed bracket assembly onto the rear housing at the photographed points.
Install the 3-Inch Projector and Trim
Install the 3-inch projector directly, route the wiring and fit the supplied outer trim panel.
Cut Only the Interference Area
Remove the trim panel and locally cut the marked section so it clears the upper portion of the 3-inch projector.
Detailed Installation Gallery
Match the Brackets, Projectors, Trim Panels and Wiring
Vehicle-Specific Bracket Pair
Confirm the left/right ID.3 mid/low-spec bracket assemblies, posts and pre-installed structural pieces.
3-Inch Projector Pair
Match the primary 3-inch projectors to the direct-mount positions and verify rear clearance.
1.5–1.8-Inch Matrix Projectors
Install the universal compact matrix projectors in the smaller bracket positions with the supplied clips.
Trim Panels and Hardware
Confirm the left/right outer trim panels, clips, fasteners and wide-voltage wiring components before opening the lamps.
Integrated Multi-Projector Layout Installed
The completed reference restores the outer lens over the fitted 3-inch and compact matrix projectors with the model-specific trim panels.
- Correct mid/low-spec headlamp confirmed
- Primary and matrix projectors secured
- Wide-voltage beam inputs verified
- Trim panel cut only at the marked interference area
- Beam functions, aim and sealing tested
Volkswagen ID.3 3-Inch + Matrix Retrofit FAQ
Which ID.3 headlamp is covered?
The supplied reference covers the pictured 2021–2023 Volkswagen ID.3 mid/low-spec headlamp. Confirm the lamp label, front signature and internal reflector layout before ordering.
Which projectors are used in this kit?
The reference shows one 3-inch projector position together with universal 1.5–1.8-inch matrix projectors on each vehicle-specific bracket assembly.
Does the headlamp need to be opened?
Yes. The pictured unit uses factory Valeo cold sealant and the reflector bowl must be removed for bracket installation.
What must be verified in the beam wiring?
Verify low-beam positive and negative signals and use a wide-voltage input for the high-beam positive and negative connections. The photographed high-beam signal is approximately 8.7 volts.
Can the factory light source be retained?
The source provides a specific optional layout when retaining the factory light source. Confirm clearance against the bracket and projector bodies before final assembly.
Is trim-panel cutting required?
Yes. After removing the trim panel, cut only the locally marked area so it does not interfere with the upper part of the 3-inch projector.
Technical reference: Based on Royalin-supplied installation photography and article 683 for the pictured 2021–2023 Volkswagen ID.3 mid/low-spec 3-inch plus matrix retrofit kit. Verify the headlamp specification, Valeo sealant, beam signals, projector dimensions, bracket hardware and trim clearance before ordering.
Related Headlight Retrofit Cases
Need This ID.3 3-Inch + Matrix Kit?
Send the vehicle year, headlamp label, connector, internal layout and intended projector specifications for matching.
Professional lens opening, wiring verification, controlled trim cutting, beam alignment and resealing are recommended.
