BYD
Chery
Great Wall / Haval
Geely
MG
Volkswagen Golf Sportsvan Mid/Low-Trim Projector Retrofit
A source-based reference for the pictured Golf Sportsvan mid/low-trim headlamp, covering the outer projector bracket, second-generation Volkswagen decoder, factory-shroud fitment and rear-housing installation.
Golf Sportsvan Mid/Low TrimMid/Low-Trim Outer Projector Bracket Application
This bracket is for the pictured mid/low-trim headlamp and is not interchangeable with the high-trim adaptive bracket.
- Model
- Volkswagen Golf Sportsvan
- Years
- 2019–2020 reference
- Trim
- Mid / low-trim headlamp
- Position
- Outer projector position
- Decoder
- Second-generation VW decoder
Confirm the mid/low-trim headlamp before ordering.
Use a square projector if the original shroud will be retained.
High-power projector harness power must be taken from the decoder IN side.
Decoder Connection, Beam Signals and Shroud Choice
Connect the Supplied Harness First
Prepare the decoder harness before connecting the factory driver and replacement projector.
Use the Correct Decoder Ports
Connect the factory headlamp driver to IN and the supplied solenoid adapter to OUT.
Verify the Vehicle Pins
The pictured reference identifies low-beam positive, negative and high-beam positive. Verify polarity before wiring.
Match the Trim, Decoder and Projector Shape
Reference Applies To
- 2019–2020 Golf Sportsvan mid/low-trim headlamp shown
- Matching outer-position bracket set
- Second-generation Volkswagen decoder
- Square projector with factory shroud
- Verified input-side power connection
Not Automatically Confirmed
- High-trim adaptive headlamp or bracket
- Round projector with the factory square shroud
- High-power projector powered from decoder OUT
- Other model years or headlamp manufacturers
- Unverified connector polarity
Send Photos for Verification
Provide the year, trim level, headlamp label, factory shroud, connector and projector shape and dimensions.
Golf Sportsvan Mid/Low-Trim Installation Sequence
Open the Valeo Cold-Sealed Headlamp
Open the factory Valeo cold-sealed lens using controlled heat and an approved headlamp-opening process.
Remove the Factory Projector
Remove the original projector and retain the factory shroud, carrier and reusable fasteners.
Remove the Factory Projector Shroud
Separate the projector shroud and inspect its mounting tabs before choosing the replacement projector.
Trim the Marked Shroud Tab
Cut only the marked tab needed for bracket and projector clearance.
Secure the Shroud to the Bracket
Rivet the upper section, secure the lower mounting points and confirm the shroud is centered.
Reinstall the Assembly in the Housing
Mount the completed bracket and projector assembly in the rear housing, then verify wiring and clearance before sealing.
Detailed Installation Gallery
Match the Bracket, Decoder, Projector and Shroud
Mid/Low-Trim Bracket Set
Confirm the dedicated left/right brackets, retaining clips and fasteners for the pictured headlamp.
Second-Generation VW Decoder
Connect the factory driver to the decoder IN port and the supplied adapter to the OUT port.
Projector and Shroud Choice
Use a square projector with the factory shroud, or select a separate decorative shroud for a round projector.
High-Power Projector Harness
Use a separate harness when required and take power from the decoder input side.
Projector Installed with the Selected Shroud Strategy
The completed reference shows the replacement projector and restored factory exterior installed behind the resealed lens.
- Correct mid/low-trim headlamp confirmed
- Decoder connected through the specified IN and OUT ports
- Projector shape matched to the selected shroud
- Bracket assembly secured in the rear housing
- Beam switching, fault behavior, aim and sealing require final vehicle testing
Golf Sportsvan Mid/Low-Trim Retrofit FAQ
Which Golf Sportsvan headlamp does this bracket fit?
This reference is for the pictured 2019–2020 mid/low-trim headlamp. The high-trim adaptive bracket is different and is not interchangeable.
Is a decoder required?
Yes. Article 1100 specifies the second-generation Volkswagen decoder for this application.
How should a high-power projector be powered?
Use a separate harness and take power from the decoder input side marked IN, not from its output side.
Can the factory projector shroud be retained?
Yes, but the source specifies a square projector when the factory shroud is retained.
Can a round projector be installed?
A round projector may be used only with a separately selected decorative shroud because the factory shroud is intended for a square projector.
What wiring signals are shown?
The reference identifies pin 1 as low-beam positive, pin 2 as negative and pin 4 as high-beam positive. Verify the vehicle connector before wiring.
Technical reference: Based on Royalin-supplied installation photography and article 1100 for the pictured 2019–2020 Volkswagen Golf Sportsvan mid/low-trim headlamp. Verify trim, decoder version, projector shape, wiring and shroud fitment before ordering.
Related Headlight Retrofit Cases
Need This Golf Sportsvan Retrofit Solution?
Send the vehicle year, trim level, headlamp label, factory shroud, connector and projector dimensions for matching.
Professional lamp opening, decoder wiring, controlled trimming, beam aiming and resealing are recommended.