BYD
Chery
Great Wall / Haval
Geely
MG
Volkswagen CC / Arteon Inner-Position Projector Retrofit
A source-based reference for adding a projector at the inner headlamp position, with separate installation paths for the high-spec projector lamp and low-spec turn-signal lamp.
CC / Arteon Inner Headlamp PositionIdentify the Inner Position before Installation
The inner position serves different functions across trim levels. High-spec lamps use an inner low-beam projector; low-spec lamps use an inner turn signal and require the supplied ball joint when converted.
- Model
- Volkswagen CC / Arteon
- Years
- 2019–2023 reference range
- High Spec
- Inner low-beam projector
- Low Spec
- Inner turn-signal position
- Projector
- Slim body recommended
- Ball Joint
- Low-spec conversion only
Remove the original inner low-beam projector and install the bracket.
Clear the turn-signal position and replace the factory ball joint.
Use a compact body and test-fit the restored trim panel.
High-Spec and Low-Spec Headlamp Differences
High-Spec Inner Low Beam
The inner position is already a projector. Remove its trim and original projector before installing the replacement bracket.
Low-Spec Turn Signal
The inner position is the turn signal. This path requires clearing the position and fitting the supplied ball joint.
Bracket Hardware
Install the supplied clips and fasteners in the photographed positions before fitting the bracket to the housing.
Match the Correct Trim-Level Installation Path
Reference Applies To
- 2019–2023 CC / Arteon lamps shown
- High-spec inner low-beam replacement
- Low-spec turn-signal conversion
- Vehicle-specific left/right brackets
- Slim-projector installation
Not Automatically Confirmed
- Other headlamp years or suppliers
- Using low-spec ball joints on high-spec lamps
- Deep projector bodies
- Unverified trim-panel clearance
- Removing unrelated turn-signal components
Send Photos for Verification
Provide the model year, full headlamp front, label, inner position, rear housing and desired projector.
CC / Arteon Inner-Position Installation Sequence
Identify the Headlamp Version
Confirm whether the inner position is the high-spec low-beam projector or the low-spec turn signal before selecting the installation path.
Remove the Trim Panel
For the high-spec version, remove the inner trim panel to expose and remove the factory projector.
Install the High-Spec Bracket
Fit the bracket in the high-spec inner position and install a recommended slim projector.
Prepare the Low-Spec Ball Joint
For the low-spec turn-signal version, remove the factory ball joint and install the supplied ball joint as shown.
Install the Low-Spec Bracket
Secure the bracket in the cleared turn-signal position and install the slim projector.
Restore the Trim and Test
Fit a suitable projector shroud, restore the trim panel, check clearance and aim, then complete beam testing.
Detailed Installation Gallery
Match the Brackets, Ball Joints, Projectors and Shrouds
Inner-Position Brackets
Confirm the dedicated left/right brackets for the 2019–2023 CC / Arteon headlamp.
Low-Spec Ball Joints
Use the supplied ball joints only for the low-spec turn-signal-position conversion.
Slim Projectors
Select a slim projector body to preserve rear depth and front trim clearance.
Projector Shrouds
Match the shrouds after the projector is positioned and the original trim panel is test-fitted.
Inner-Position Projector Installed
The completed reference shows the slim projector and suitable shroud installed with the headlamp trim restored.
- Correct trim level identified
- Matching installation path followed
- Low-spec ball joint used only where required
- Slim projector and shroud clearance verified
- Beam alignment and headlamp functions tested
CC / Arteon Inner-Position Retrofit FAQ
Which headlamp versions are covered?
The reference shows both high-spec and low-spec 2019–2023 CC / Arteon headlamps. On the high-spec lamp the inner position is a low-beam projector; on the low-spec lamp it is the turn-signal position.
Are the two installation paths identical?
No. The high-spec version replaces the inner projector directly, while the low-spec turn-signal version removes the factory ball joint and uses the supplied ball joint before the bracket is installed.
When are the supplied ball joints used?
They are used only when converting the low-spec turn-signal position. They are not required for the pictured high-spec projector replacement path.
What projector body is recommended?
The supplied reference recommends a slim projector because the inner position has limited depth and trim clearance.
Must the trim panel be removed?
Yes. Remove the appropriate trim panel for either version, install the bracket and projector, then restore the panel after checking clearance.
Can the original shroud always be retained?
Not automatically. Select a suitable projector shroud after checking the projector position, front appearance and interference with the restored trim panel.
Technical reference: Based on Royalin-supplied installation photography and article 666 for the pictured 2019–2023 Volkswagen CC / Arteon headlamps. Verify trim level, inner-position function, ball-joint requirement, projector depth and trim clearance before ordering.
Related Headlight Retrofit Cases
Need This CC / Arteon Inner-Position Bracket?
Send the model year, trim level, headlamp label, inner-position photos and projector specifications for matching.
Professional trim removal, bracket installation, projector alignment and complete function testing are recommended.