BYD
Chery
Geely
MGToyota Land Cruiser Prado LC250 Matrix Retrofit
A source-based installation reference for replacing the pictured LC250 LED reflector bowls with a four-projector matrix bracket system.
Prado LC250 LED HeadlampFour-Projector System for the LC250 LED Reflector-Bowl Headlamp
The supplied kit reference shows two pairs of matrix projectors, the main support bracket, mounting plates, trim panels, fasteners and the original LED reflector bowls.
- Model
- Toyota Land Cruiser Prado LC250
- Year
- 2024 reference
- Headlamp
- LED reflector-bowl configuration shown
- Projectors
- Four units, 1.5–1.8 inch format
- Trim
- Upper/lower panels and DRL restored
Confirm both projector pairs, brackets, base plates, trim panels and hardware.
Remove only the highlighted internal ribs and do not exceed the illustrated limit.
Return the trim panels and daytime running light after installation.
Identify Low-Beam and High-Beam Connections
Main Light Connections
The annotated source identifies the blue connection as low beam, the red connection as high beam and the center red connector as the low-beam light source.
OEM Butyl Sealant
Heat the housing and open it carefully with a scraper while preserving the lens channel and reusable seal area.
Original Light Source Removal
Remove the OEM bulb and clean the adhesive only at the indicated point before preparing the internal carrier.
Confirm the LC250 Headlamp Before Ordering
Reference Applies To
- 2024 Toyota Prado LC250 shown
- LED reflector-bowl headlamp configuration
- Four-projector matrix bracket kit shown
- 1.5–1.8 inch projector format labeled
- Upper/lower trim and DRL restoration
Not Automatically Confirmed
- Other LC250 headlamp specifications
- Other years or regional carriers
- Previously modified housings
- Different projector body dimensions
- Unverified connector assignments
Send Photos for Verification
Provide the vehicle year, headlamp label, front/rear housing, reflector bowls, connectors, internal carrier and projector dimensions.
Remove the Reflector Bowl and Prepare the Base-Plate Area
Remove the Trim Panel
Carefully remove the lower trim panel, then detach the gray trim and OEM reflector bowl.
Cut the Highlighted Ribs
Use a utility knife on the marked internal ribs. Work in small increments and do not cut beyond the final limit shown in the source.
Install the Base Plate
After the screw is removed and the indicated hole is drilled, install the base plate in the prepared position.
LC250 Matrix Bracket Installation Sequence
Remove the OEM Reflector Bowl
Remove the original reflector-bowl assembly and retain the reusable components shown with the kit.
Complete Controlled Trimming
Finish the highlighted cuts carefully and confirm that no excessive material has been removed.
Secure and Seal the Base Plate
Use the supplied screw and adjuster, add the two extended screws, then fill the recessed area with sealant.
Install the Main Bracket
Install the main bracket and confirm that its retaining clip is fully seated.
Mount the Matrix Projectors
Install the four-projector matrix bracket on the main support; leave the identified screw loose until the trim is installed.
Restore Trim and Test
Install the lower and upper trim panels, restore the DRL, tighten final hardware, test both beams and reseal the headlamp.
Detailed Installation Gallery
Match the Matrix Retrofit as a Complete Kit
Main Bracket & Base Plate
Confirm the main carrier, base plates, retaining clip, adjuster and extended screws.
Four Matrix Projectors
Use two matched pairs in the labeled 1.5–1.8 inch format.
Beam Connections
Verify low-beam, high-beam and light-source connector assignments before operation.
Trim & DRL Parts
Retain and restore the upper/lower trim panels and daytime running light.
Four Matrix Projectors Installed
The completed source image shows the matrix projector bank, upper and lower trim and daytime running light restored inside the original headlamp.
- Four matched matrix projectors installed
- Main bracket and base plates secured
- Controlled housing cuts completed
- Upper/lower trim and DRL restored
- Beam testing, aiming and resealing required
2024 Toyota Prado LC250 Matrix Retrofit FAQ
Which Prado LC250 headlamp is covered?
The supplied reference covers the pictured 2024 Toyota Land Cruiser Prado LC250 LED reflector-bowl headlamp.
What is included in the matrix kit?
The source shows two sets of matrix projectors, brackets and hardware together with the OEM LED reflector bowls.
Which projector size is shown?
The supplied matrix brackets are labeled compatible with 1.5–1.8 inch projectors.
Does the headlamp housing require trimming?
Yes. Cut only the highlighted internal ribs and stop at the illustrated limit; excessive cutting can weaken or damage the housing.
What must be restored after installation?
Reinstall the upper and lower trim panels, daytime running light and exterior trim after the matrix brackets are secured and tested.
Technical reference: Based on Royalin-supplied installation photography for the pictured LC250 LED reflector-bowl configuration. Verify the headlamp label, carrier, connector assignments and projector dimensions before ordering.
Related Headlight Retrofit Cases
Need This LC250 Matrix Retrofit Kit?
Send the vehicle year, headlamp label, housing, reflector bowls, internal carrier and connector photos for verification.
Professional cutting, electrical testing, installation, sealing and beam aiming are recommended.
