BYD
Chery
Geely
MGToyota Land Cruiser Prado LC250 Round-Headlamp Projector Retrofit
A source-based reference for the pictured LC250 round headlamp, covering bracket fitment, beam signals, rear-housing clearance, DRL trim preparation and projector mounting.
LC250 Round HeadlampRound-Headlamp Bracket Architecture for the 2024–2025 LC250
The supplied kit contains separate left and right steel brackets with clips and adjustment hardware for the pictured round-headlamp assembly.
- Model
- Toyota Land Cruiser Prado LC250
- Years
- 2024–2025 reference
- Headlamp
- Round-headlamp configuration shown
- Bracket
- Side-specific left/right set
- Seal
- OEM butyl-sealed housing
Install the supplied clips and adjustment pieces in the shown orientations.
Reshape the rear housing and DRL trim only at the marked locations.
Add the specified nut at the front projector mounting point.
Bracket, Signal and Housing Details
Install the Bracket Clips
Prepare each side-specific bracket with the supplied clips and adjustment hardware.
Verify Beam Signals
The source marks the combined high/low-beam and low-beam positive/negative points. Confirm them electrically before connection.
Create Rear Clearance
Press down only the highlighted rear-housing section without damaging nearby mounts or wiring.
Confirm the Round-Headlamp Configuration
Reference Applies To
- 2024–2025 Prado LC250 shown
- Round-headlamp configuration
- Side-specific bracket kit
- OEM butyl-sealed housing
- Compatible DRL shroud
Not Automatically Confirmed
- High-spec square headlamp
- LED reflector-bowl version
- Other years or regional housings
- Previously modified lamps
- Unverified projector dimensions
Send Photos for Verification
Provide the year, headlamp label, front/rear views, internal carrier, wiring and projector dimensions.
LC250 Round-Headlamp Installation Sequence
Confirm Beam Signals
Identify and verify the source-marked beam signal points before wiring.
Open the Butyl-Sealed Housing
Heat and open the OEM butyl-sealed headlamp while protecting the channel.
Reshape the Rear Housing
Press down only the highlighted section to create clearance.
Trim the DRL Piece
Remove a small amount from the underside of the DRL trim.
Mount the Projector
Install the bracket and projector, adding the specified front nut.
Restore the Front Trim
Use a compatible DRL shroud and widen the OEM trim opening as shown.
Detailed Installation Gallery
Match the Retrofit as a Complete System
Left/Right Bracket Set
Confirm both side-specific brackets, clips and adjustment sleeves.
Compatible Projector
Match the projector body and front mounting pattern.
Signal Connections
Verify high/low-beam and low-beam positive/negative circuits.
DRL Shroud & Trim
Use a compatible shroud and retain the OEM trim after clearance work.
Projector and DRL Trim Restored
The completed reference shows the projector installed behind a compatible DRL shroud with the front trim opening adjusted for clearance.
- Side-specific bracket secured
- Rear-housing clearance completed
- DRL trim underside adjusted
- Additional front nut installed
- Beam testing, aiming and resealing required
Prado LC250 Round-Headlamp Retrofit FAQ
Which Prado headlamp is covered?
The reference covers the pictured 2024–2025 Toyota Land Cruiser Prado LC250 round-headlamp configuration.
Is the bracket side-specific?
Yes. The supplied kit shows separate left- and right-hand projector brackets with clips and adjuster components.
Which beam signals are identified?
The source marks a combined high/low-beam signal and separate low-beam positive and negative points. Verify each circuit before connection.
Does the housing require modification?
Yes. Press down only the highlighted rear-housing area and trim a small amount from the underside of the DRL trim.
What is required at final assembly?
Use a compatible DRL shroud, widen the OEM trim opening as shown, secure the projector with one additional front nut, then test, aim and reseal the headlamp.
Technical reference: Based on Royalin-supplied installation photography for the pictured 2024–2025 LC250 round-headlamp configuration. Verify the headlamp label, bracket points, projector dimensions and beam signals before ordering.
Related Headlight Retrofit Cases
Need This LC250 Round-Headlamp Retrofit Solution?
Send the vehicle year, headlamp label, housing, carrier, connector and clearance photos for matching.
Professional housing work, electrical testing, installation, sealing and beam aiming are recommended.
