BYD
Chery
Great Wall / Haval
Geely
MG
Toyota Land Cruiser Prado LED Low-Beam Projector Retrofit
A structured retrofit reference for the pictured Land Cruiser Prado headlight, covering OEM low-beam removal, reflector preparation, bracket mounting and LED projector installation.
Land Cruiser Prado HeadlightLand Cruiser Prado Projector Bracket Application
The supplied reference identifies a dedicated bracket and vehicle-specific bracket arrangement for the pictured 2018–2019 Prado headlight.
- Model
- Toyota Land Cruiser Prado
- Years
- 2018–2019 reference range
- Edition
- LED Low-Beam Headlight
- Headlight
- OEM headlight assembly shown
- Low Beam
- OEM reflector bowl retained
Retain the OEM reflector bowl and decorative shroud and secure it with self-tapping screws in the shown positions.
Install the LED projector on the Prado bracket, then verify clearance and optical alignment.
Check rear housing clearance, reinstall the leveling motor and verify low-beam operation before sealing.
Identify Wiring and Prepare the Projector Assembly
OEM Low-Beam Removal
Confirm the low-beam assembly, bracket orientation and reusable OEM parts before modification.
Reflector Preparation
Verify the LED projector wiring and low-beam operation before final assembly.
Bracket and Clearance Check
Confirm the projector headlight, projector body, bracket orientation and available rear clearance before installation.
Confirm the Land Cruiser Prado Configuration
Reference Applies To
- 2018–2019 Toyota Land Cruiser Prado shown
- 2018–2019 Prado headlight with vehicle-specific projector bracket
- Application-specific metal bracket
- OEM reflector bowl and decorative shroud retained
- compatible LED projector format shown
Not Automatically Confirmed
- Other years or headlight configurations
- Other years, regions or internal carriers
- Previously modified housings
- Unverified projector dimensions
- Unverified sealant condition or prior repairs
Send Photos for Verification
Provide model year, headlight label, front/rear views, original projector, carrier, connector and trim photos.
Reflector Preparation, Bracket Hardware and Projector Mounting
Confirm vehicle-specific projector bracket, assemble the retaining clips and hardware, and secure the decorative shroud without contacting the lens cover.
Bracket Orientation
Open the lens cover, inspect the low-beam assembly and protect all reusable OEM parts.
Reflector Surface Preparation
Grind the two raised reflector tabs and mounting surface flat, then clean all debris before bracket installation.
Bracket Positioning
Secure the decorative shroud with self-tapping screws at the shown points, keeping its inner edge against the lens cover without pressure.
Land Cruiser Prado Installation Sequence
Open and Inspect the Headlight
Open the lens cover, inspect the low-beam assembly and protect all reusable OEM parts.
Remove the Low-Beam Assembly
Release the three OEM clips, remove the low-beam assembly and detach the original projector.
Prepare the Reflector Bowl
Grind the two raised tabs and mounting surface flat, then remove all metal dust from the reflector.
Install Spacer and Bracket
Insert the spacer washer, reinstall the screw through the OEM hole, position the bracket and tighten the nuts.
Install the LED Projector
Insert the spacer washer, position the bracket and install the compatible LED projector.
Restore OEM Parts and Test
Restore the OEM reflector bowl and leveling motor, verify low-beam alignment and reseal the headlight.
Detailed Installation Gallery
Match the Land Cruiser Prado LED Low-Beam Projector Retrofit as a Complete Kit
Land Cruiser Prado Bracket Set
Use the vehicle-specific left and right metal brackets and supplied guide posts.
Compatible Projector
Confirm projector body, mounting pattern, output and rear clearance.
Leveling Motor & Wiring
Retain the OEM leveling motor and verify low-beam wiring before final sealing.
Fasteners & OEM Parts
Retain the OEM shroud and ring, and use the supplied clips, studs and screws.
Projector Installed, OEM Appearance Restored
The completed reference shows the new projector installed inside the original projector headlight with the exterior assembly restored.
- Application-specific bracket and guide posts installed
- OEM shroud restored in its original position
- Projector operation and alignment verified
- OEM reflector bowl and decorative shroud secured with self-tapping screws and restored
- Headlight resealed and beam aiming required
2018–2019 Toyota Land Cruiser Prado Retrofit FAQ
Which Land Cruiser Prado headlight is covered?
The pictured 2018–2019 Toyota Land Cruiser Prado headlight.
Does the headlight need to be resealed?
Yes. Verify the projector wiring and test both beams before closing the housing.
Must the OEM reflector bowl be reused?
Yes. Retain and reinstall the original reflector bowl.
How is the OEM reflector bowl restored?
Use self-tapping screws at the shown points without placing excessive pressure on the lens cover.
Which projector format is shown?
The reference shows a compatible projector installed from the rear of the bracket.
Technical reference: Based on Royalin-supplied fitment documentation and installation photography for the configuration shown. Verify year, edition, headlight label, connector and carrier before ordering.
Related Headlight Retrofit Cases
Need This Land Cruiser Prado Retrofit Solution?
Send the model year, edition, headlight label, front/rear views, projector, connector and internal carrier photos for verification.
Professional electrical testing, installation, sealing and beam aiming are recommended.