BYD
Chery
Geely
MGToyota Land Cruiser Prado Quad-Projector Retrofit
A source-based reference for upgrading the pictured Prado headlamp with a low-beam LED projector bracket and an optional high-beam projector metal kit.
Completed Quad-Projector HeadlampTwo Retrofit Paths for the Prado Headlamp
The supplied documentation presents a dedicated low-beam bracket and a separate high-beam metal bracket and shroud set. They can be installed as a single low-beam upgrade or combined as the pictured quad-projector system.
- Model
- Toyota Land Cruiser Prado
- Years
- 2014–2016 reference range
- Low Beam
- Vehicle-specific LED projector bracket
- High Beam
- Metal bracket and decorative shroud kit
- Housing
- OEM and aftermarket details shown
The documentation includes a completed low-beam-only retrofit.
The high-beam kit adds a second projector and metal decorative shroud.
Confirm whether the headlamp is OEM or aftermarket before selecting the mounting method.
Confirm the Decoder, Sealant and Mounting Points
Toyota-Compatible Decoder
The source identifies white as low-beam positive, blue as low-beam negative and gray-brown as the signal wire. Verify the vehicle before connecting.
OEM Cold Sealant
The pictured OEM headlamp uses cold sealant and is described as relatively easy to open. Work carefully to preserve the sealing channel.
Aftermarket Housing Difference
The illustrated aftermarket headlamp uses a threaded rod at the identified mounting point. Do not assume the OEM mounting detail is identical.
Verify the Headlamp Before Ordering
Reference Applies To
- 2014–2016 Prado headlamp shown
- Low-beam bracket shown in the source
- Optional high-beam metal bracket and shroud
- OEM and pictured aftermarket housings
- Toyota-compatible decoder arrangement shown
Not Automatically Confirmed
- Other model years or headlamp designs
- Unpictured aftermarket housings
- Previously modified mounting points
- Unverified projector body dimensions
- Different wire colors or control logic
Send Photos for Verification
Provide the vehicle year, headlamp label, front and rear housing, low/high-beam assemblies, mounting points and connectors.
Install the Vehicle-Specific Low-Beam Bracket
Remove the Shroud Screws
Remove the two screws from the projector decorative shroud before releasing the lower OEM retaining clips.
Prepare the Projector
Apply adhesive to the front of the projector as shown, then install it on the dedicated low-beam bracket.
Install the Bracket
Position the vehicle-specific bracket directly in the original low-beam location and confirm the retaining points.
Restore the OEM Shroud
Reinstall the OEM decorative shroud and secure it with the original-position locking nut.
Build and Install the High-Beam Projector Assembly
Mount the High-Beam Projector
Secure the high-beam projector directly to the dedicated metal bracket.
Attach the Metal Shroud
Fasten the metal decorative shroud to the bracket at the three highlighted points.
Trim the Plastic Shroud
Trim the indicated plastic decorative-shroud edge, then snap it into place.
Install on the Rear Housing
Position the completed high-beam assembly on the rear housing and confirm the correct mounting detail.
Inspect the Rear Mount
Check the rear installation, fastener seating and available housing clearance.
Test and Restore
Test both beam positions, verify aim and function, restore the lens cover and reseal the headlamp.
Detailed Installation Gallery
Match the Retrofit as a Complete System
Low-Beam Bracket Set
Confirm the left/right brackets, retaining clips and supplied hardware.
Compatible Projectors
Confirm low/high-beam projector bodies, mounting patterns and rear clearance.
Decoder & Wiring
Use a Toyota-compatible decoder and verify all wire functions on the vehicle.
High-Beam Metal Kit
Confirm the high-beam bracket, metal shroud, plastic trim and mounting hardware.
Low and High Beam Projectors Installed
The completed source image shows both projector positions restored inside the original exterior headlamp assembly.
- Vehicle-specific low-beam bracket installed
- High-beam metal bracket and shroud installed
- OEM or aftermarket mounting detail matched
- Decoder wiring checked before final connection
- Beam operation, aim and resealing still required
2014–2016 Toyota Prado Retrofit FAQ
Which Prado headlamp configuration is covered?
The supplied reference covers the pictured 2014–2016 Toyota Land Cruiser Prado headlamp and shows both OEM and aftermarket housing details.
Can the low-beam bracket be used without the high-beam kit?
Yes. The reference shows a completed single low-beam retrofit as well as the combined quad-projector configuration.
Is a decoder required?
Use a Toyota-compatible decoder and confirm the pictured wire functions before final connection.
Are OEM and aftermarket headlamps installed identically?
No. The supplied reference shows different mounting details; the aftermarket housing uses a threaded-rod mounting point.
Does the high-beam trim require modification?
Yes. The metal shroud attaches to the bracket, and the plastic decorative shroud edge is trimmed before it is snapped into place.
Technical reference: Based on Royalin-supplied installation photography for the pictured configuration. Verify the year, headlamp manufacturer, mounting points, projector dimensions and wiring before ordering.
Related Headlight Retrofit Cases
Need This Prado Retrofit Solution?
Send clear photos of the headlamp label, housing, low/high-beam assemblies, mounting points and connectors for verification.
Professional electrical testing, installation, sealing and beam aiming are recommended.
