BYD
Chery
Geely
MGToyota Land Cruiser LC300 Matrix Retrofit
A source-based reference for the pictured LC300 mid/low-spec headlamp, covering two supported matrix layouts, signal wiring, spacer placement, main bracket mounting and trim restoration.
LC300 Matrix HeadlampTwo Matrix Layouts for the 2022 Land Cruiser LC300
The supplied kit contains a complete carrier, projector brackets, shrouds, trim panels, spacers and fasteners for the pictured mid/low-spec LC300 headlamp.
- Model
- Toyota Land Cruiser LC300
- Years
- 2022 reference
- Headlamp
- Mid/low-spec headlamp shown
- Bracket
- Five-projector or three-plus-two layout
- Seal
- OEM butyl-sealed housing
Fit the supplied metal shroud panels in the orientations shown.
Choose five bi-LED projectors or three bi-LED units plus two independent high beams.
Install the shaped plastic block correctly; do not turn it upside down.
Shroud, Spacer and Wiring Details
Install the Shroud Panels
Attach the supplied shroud panels to the main carrier in the shown positions.
Orient the Plastic Block
Install the shaped block at the highlighted bracket point and do not install it upside down.
Verify the Four Signal Wires
Verify low-beam positive/negative and high-beam positive/negative wires before connecting the matrix system.
Confirm the Mid/Low-Spec LC300 Headlamp
Reference Applies To
- 2022 Toyota Land Cruiser shown
- Mid/low-spec headlamp configuration
- Complete matrix bracket and trim kit
- OEM butyl-sealed housing
- Verified matrix projector layout
Not Automatically Confirmed
- High-spec LC300 headlamp designs
- Other LC300 model years
- Other years or regional housings
- Previously modified lamps
- Unverified projector body sizes
Send Photos for Verification
Provide the year, headlamp label, front/rear views, internal carrier, wiring and projector dimensions.
Toyota Land Cruiser LC300 Matrix Installation Sequence
Open the Front Cover
Open the OEM butyl-sealed headlamp carefully while preserving the sealing channel.
Remove the OEM Reflector Bowl
Remove the reflector-bowl assembly to expose the main bracket mounting area.
Install the Main Bracket
Place the assembled matrix bracket into the rear housing and confirm all mounting points.
Install the Lower Small Trim
Fit the lower small trim panel at the marked bracket position.
Install the Lower Trim Panel
Install the larger lower trim panel and verify clearance around the projector row.
Test and Complete the Assembly
Confirm projector alignment, low/high-beam operation and trim fit before resealing the front cover.
Detailed Installation Gallery
Match the LC300 Matrix Retrofit as a Complete System
Main Bracket & Trim Set
Confirm the main carrier, shrouds, lower trim panels, fasteners and spacers.
Matrix Projector Option
Choose five bi-LED units or the documented three-plus-two high-beam configuration.
Black Plastic Spacers
Install the correct-height spacers at the highlighted points and keep the shaped block upright.
Low/High-Beam Wiring
Verify all four source-identified signal wires before operation.
LC300 Matrix Projector Array Installed
The completed reference shows the matrix projector array, lower trim panels and front cover restored inside the original LC300 headlamp.
- Main matrix carrier secured
- Selected projector layout assembled
- Black plastic spacers installed
- Lower trim panels restored
- Beam testing, aiming and resealing required
Toyota Land Cruiser LC300 Matrix Retrofit FAQ
Which LC300 headlamp is covered?
The supplied reference covers the pictured 2022 Toyota Land Cruiser LC300 mid/low-spec headlamp.
What matrix configurations are shown?
Option A uses five bi-LED matrix projectors. Option B uses three bi-LED projectors plus two independent high beams.
How is the lamp wired?
The source identifies black/blue as low-beam positive, white/blue as low-beam negative, white/black as high-beam positive and yellow/black as high-beam negative. Verify the vehicle before connection.
Why are black plastic spacers required?
The source calls for black plastic spacers at the highlighted mounting points to raise and align the projector assembly. The shaped block must not be installed upside down.
What OEM parts are removed and restored?
Remove the OEM reflector bowl, retain the housing and front cover, then install the bracket assembly and lower trim panels before testing and resealing.
Technical reference: Based on Royalin-supplied installation photography for the pictured 2022 Toyota Land Cruiser LC300 mid/low-spec configuration. Verify the headlamp label, bracket points, projector dimensions and beam signals before ordering.
Related Headlight Retrofit Cases
Need This LC300 Matrix Retrofit Solution?
Send the vehicle year, headlamp label, housing, original reflector bowl, internal carrier, connectors and projector-layout photos for matching.
Professional housing work, electrical testing, installation, sealing and beam aiming are recommended.
