BYD
Chery
Geely
MGToyota Highlander Full Matrix Bracket Retrofit
A source-based reference for the pictured 2022 Highlander full matrix headlamp, covering factory-shroud preparation, three projector positions, mounting order, wiring and rear-cover clearance.
2022 Highlander Full MatrixFull Matrix Bracket Application for the 2022 Highlander
The supplied reference identifies a dedicated full matrix carrier, three projector adapter positions, mounting hardware and optional low-beam replacement plate.
- Model
- Toyota Highlander
- Years
- 2022 reference
- Headlamp
- Full matrix unit shown
- Bracket
- Three-projector matrix carrier
- Sizes
- 1.5–1.8 and 1.5–1.7 inch
Match each projector position to the size range stated in the source.
Cut and grind only the marked areas before installing the carrier.
Confirm wiring, inner-projector angle and rear-cover clearance.
Matrix Carrier, Projector Sizes and Shroud Details
Prepare the Factory Shroud
Remove marked sections and grind the raised contact point flush.
Match Projector Sizes
Use the specified 1.5–1.8 and 1.5–1.7 inch projector ranges.
Set the Inner Projector Angle
Angle the innermost mounting tab upward and grind only as needed.
Confirm the 2022 Highlander Full Matrix Headlamp
Reference Applies To
- 2022 Toyota Highlander full matrix headlamp shown
- Application-specific left/right carrier set
- Three projector positions and matching adapters
- OEM butyl-sealed housing
- Projector sizes match the stated ranges
Not Automatically Confirmed
- Standard non-matrix Highlander headlamps
- Highlander models outside the pictured 2022 application
- Other regional headlamp housings
- Previously modified shrouds or carriers
- Projectors outside the specified size ranges
Send Photos for Verification
Provide the vehicle year, headlamp label, front/rear views, reflector bowl and projector dimensions.
2022 Highlander Full Matrix Installation Sequence
Open the Butyl-Sealed Housing
Open the original butyl-sealed headlamp without baking and protect the sealing channel.
Remove Trim and Projector Parts
Remove the factory trim bezel and original projector components from the housing.
Prepare the Factory Shroud
Cut away the marked shroud areas and grind the identified raised section flush.
Position the Projector Loosely
Place the projector on the carrier without fully tightening it, then insert the lower factory-shroud section first.
Secure the Matrix Carrier
Tighten the upper point, remaining three points and the inner mounting tab in the shown sequence.
Install Rear Cover and Test
Fit the rear cover, verify all three projector positions, test beam operation and reseal the housing.
Detailed Installation Gallery
Match the Full Matrix Retrofit as a Complete System
Full Matrix Bracket Kit
Confirm both main carriers, three projector adapters, clips and fasteners.
Three Compatible Projectors
Match one 1.5–1.8 inch outer projector and two 1.5–1.7 inch projectors.
Prepared Factory Shroud
Retain the factory shroud after the marked cutting and flush grinding.
Wiring and Rear Cover
Verify connector polarity, inner-projector angle and rear-cover clearance.
Full Matrix Carrier Installed
The completed reference shows the three-projector full matrix carrier installed behind the prepared factory trim with the rear cover restored.
- Factory shroud cut and raised section ground flush
- Three projector positions assembled
- Inner mounting tab angle verified
- Rear cover and connector clearance confirmed
- Beam aim, operation and sealing require final verification
2022 Toyota Highlander Full Matrix Retrofit FAQ
Which Toyota Highlander headlamp is covered?
This reference covers the pictured 2022 Toyota Highlander full matrix headlamp and its application-specific multi-projector bracket kit.
How many projector positions are provided?
The source shows three projector positions in the full matrix carrier: one outer position and two additional positions.
Which projector sizes are referenced?
The outer position accepts approximately 1.5–1.8 inch projectors, while the other two positions accept approximately 1.5–1.7 inch projectors.
What must be modified on the factory shroud?
Remove the marked shroud areas and grind the raised section flush so the projector carrier can sit correctly.
Is there an adapter for replacing the low-beam projector?
Yes. The source shows a separate adapter plate for a 1.5–1.8 inch projector when replacing the low-beam unit.
Technical reference: Based on Royalin-supplied installation photography for the pictured 2022 Toyota Highlander full matrix headlamp. Verify the label, carrier points, projector sizes, wiring and rear-cover clearance before ordering.
Related Headlight Retrofit Cases
Need This Highlander Full Matrix Solution?
Send the vehicle year, headlamp label, factory shroud, carrier points, projector sizes and connector wiring for matching.
Professional headlamp opening, controlled cutting, wiring, installation, sealing and beam aiming are recommended.
