BYD
Chery
Great Wall / Haval
Geely
MG
Toyota Highlander Second-Generation Trim Bezel Upgrade
A source-based reference for the second-generation heat-resistant trim bezel and matching matrix bracket, covering die-cast aluminum inserts, groove fitment, optical-center adjustment and rear-mounted projectors.
Second-Generation Trim BezelSecond-Generation Bezel and Matrix Bracket Application
The supplied reference identifies a heat-resistant bezel, one-piece die-cast aluminum inserts and an adjustable matrix bracket for the pictured 2022–2024 Highlander headlamp.
- Model
- Toyota Highlander
- Years
- 2022–2024 reference
- Trim
- Second-generation heat-resistant bezel
- Insert
- One-piece die-cast aluminum
- Bracket
- Adjustable 3-inch-plus matrix carrier
Use the second-generation bezel and matching die-cast aluminum inserts.
Insert the aluminum tabs into their matching grooves and secure the rear screw.
Select from five mounting holes; the middle position suits most projectors.
Aluminum Insert, Optical Center and Projector Mounting
Engage the Matching Grooves
Insert the aluminum tabs directly into the matching bezel grooves.
Adjust the Optical Center
Use the five-hole vertical range and the middle position for most projectors.
Match the Projector Adapter
Use the guide post, dual-beam positions or supplied sleeves for cube projectors.
Confirm the 2022–2024 Highlander Bezel Configuration
Reference Applies To
- 2022–2024 Toyota Highlander headlamp shown
- Second-generation heat-resistant trim bezel
- Matching one-piece die-cast aluminum inserts
- Adjustable matrix bracket and hardware
- Projector format matches the shown adapters
Not Automatically Confirmed
- First-generation or other trim-bezel designs
- Highlander models outside 2022–2024
- Other regional headlamp housings
- Damaged accessory grooves or mounting tabs
- Unverified projector and adapter combinations
Send Photos for Verification
Provide the vehicle year, headlamp label, front/rear views, reflector bowl and projector dimensions.
Second-Generation Trim Bezel Installation Sequence
Remove the Passenger-Side Accessory
Remove the passenger-side accessory from the second-generation trim bezel before fitting the aluminum insert.
Insert the Aluminum Tabs
Align the one-piece die-cast aluminum insert and push its tabs directly into the matching grooves.
Secure the Trim Bezel Rear Point
Confirm full groove engagement, then secure the rear of the insert with the specified screw.
Assemble the Matrix Bracket
Prepare the 2022–2024 Highlander matrix carrier, low-beam adapter and supplied hardware.
Select the Optical-Center Position
Use the five-hole adjustment range and start with the middle position for most projector bodies.
Rear-Mount the Projectors
Install through the guide post; use the supported 1.5-inch dual-beam positions or supplied sleeves for cube projectors.
Detailed Installation Gallery
Match the Bezel and Matrix Bracket as a Complete System
Second-Generation Trim Bezel
Confirm the matching 2022–2024 heat-resistant left/right bezel assemblies.
Die-Cast Aluminum Inserts
Install each one-piece aluminum insert into its matching grooves.
Adjustable Matrix Bracket
Use the five-hole vertical optical-center adjustment for the selected projector.
Projector Adapters and Hardware
Confirm the guide post, sleeves, screws, nuts and small-projector adapters.
Second-Generation Trim Bezel Assembled
The assembled reference shows the die-cast aluminum insert seated in the heat-resistant bezel with the rear fixing point secured.
- Passenger-side accessory removed
- Aluminum tabs seated in matching grooves
- Rear trim fixing screw installed
- Optical-center position selected for the projector
- Projector fit, alignment and clearance require final verification
2022–2024 Toyota Highlander Trim Bezel FAQ
Which Toyota Highlander models are covered?
This reference covers the pictured 2022–2024 Toyota Highlander headlamp and the second-generation heat-resistant trim bezel configuration.
What are the trim inserts made from?
The source identifies one-piece die-cast aluminum trim inserts designed for the matching bezel grooves.
What must be removed before fitting the insert?
Remove the passenger-side accessory shown, then insert the aluminum tabs directly into the matching grooves.
How is the low-beam optical center adjusted?
Five mounting holes provide vertical optical-center adjustment for different projectors; the source recommends the middle position for most projectors.
Which small projectors are supported?
Two positions accept 1.5-inch dual-beam projectors. For cube projectors, install the supplied sleeves directly as shown.
Technical reference: Based on Royalin-supplied reference photography for the pictured 2022–2024 Toyota Highlander second-generation trim bezel and matrix bracket. Verify the headlamp, bezel generation, groove positions and projector format before ordering.
Related Headlight Retrofit Cases
Need This Highlander Trim Bezel and Matrix Solution?
Send the vehicle year, headlamp photos, bezel generation, groove positions, bracket points and projector dimensions for matching.
Professional headlamp disassembly, trim assembly, projector fitment, alignment and functional testing are recommended.