BYD
Chery
Geely
MGToyota Camry US-Spec Projector Retrofit
A source-based reference for the pictured Camry US-spec headlamp, covering bracket orientation, projector spacing, beam wiring, DRL removal, front-trim clearance and light-guide restoration.
Camry US-Spec HeadlampProjector Bracket Application for the 2024–2026 Camry US-Spec Headlamp
The supplied kit contains a side-specific bracket set with accessory pieces, orientation blocks and adjustable washer spacing matched to the pictured Camry US-spec headlamp.
- Model
- Toyota Camry
- Years
- 2024–2026 reference
- Headlamp
- US-spec headlamp shown
- Bracket
- Projector thickness adjusted with washers
- Seal
- OEM hot-melt-sealed housing
Flip the accessory bracket and keep the plastic block flat side facing forward.
Tighten both inner screws first, then add outer washers as needed.
Remove the daytime running light and restore the white light-guide strip after installation.
Orientation, Wiring and Projector Details
Confirm Accessory Bracket Orientation
Install the accessory bracket in the shown flipped orientation.
Orient the Plastic Block
Keep the flat side facing forward and the protruding pin facing rearward.
Verify Beam Wiring
Verify yellow/blue low-beam and black/white high-beam wires before connection.
Confirm the Camry US-Spec Headlamp
Reference Applies To
- 2024–2026 Toyota Camry shown
- US-spec headlamp configuration
- Orientation-specific bracket and accessory hardware
- OEM hot-melt-sealed housing
- Projector thickness and trim clearance verified
Not Automatically Confirmed
- Other regional Camry headlamp versions
- Camry models outside 2024–2026
- Other years or regional housings
- Previously modified lamps
- Unverified projector thickness or wiring
Send Photos for Verification
Provide the year, headlamp label, front/rear views, internal carrier, wiring and projector dimensions.
Camry US-Spec Projector Installation Sequence
Open the Front Cover
Open the OEM hot-melt-sealed headlamp carefully and protect the sealing channel.
Remove the Daytime Running Light
Remove the DRL assembly to expose the projector bracket area.
Mount and Adjust the Projector
Loosen the inner points, mount the projector, tighten the inner screws first and add outer washers as needed.
Install the Bracket Assembly
Place the completed bracket into the rear housing and reinstall the white light-guide strip.
Trim the Front Area
Trim only the marked area as required for the selected projector and confirm clearance.
Restore, Test and Complete
Restore the front components, test low/high beam, aim the projector and reseal the headlamp.
Detailed Installation Gallery
Match the Camry US-Spec Retrofit as a Complete System
Camry US-Spec Bracket Set
Confirm the left/right brackets, accessory pieces, plastic blocks and hardware.
Compatible Projector
Match the projector thickness and use outer washers as needed.
Beam Wiring
Verify yellow/blue low-beam and black/white high-beam circuits.
DRL & Light Guide
Retain the daytime running light and white guide strip for restoration.
Camry US-Spec Projector Assembly Restored
The completed reference shows the projector bracket, white light-guide strip and front trim restored inside the original US-spec headlamp.
- Accessory bracket orientation confirmed
- Projector washer spacing adjusted
- Beam wiring verified
- DRL and white light guide restored
- Beam testing, aiming and resealing required
Toyota Camry US-Spec Projector Retrofit FAQ
Which Toyota Camry headlamp is covered?
The reference covers the pictured 2024–2026 Toyota Camry US-spec headlamp configuration.
How should the accessory bracket be installed?
Flip the accessory bracket as shown. The plastic block flat side faces forward and the protruding pin faces rearward.
Which wire colors are identified?
Yellow is low-beam positive, blue low-beam negative, black high-beam positive and white high-beam negative. Verify before connection.
How are projector thickness differences corrected?
Tighten the two inner screws first, then add washers on the outer side as needed; spacer height depends on projector thickness.
Does the front trim require modification?
The source instructs trimming the marked front area as required for the selected projector, followed by reinstalling the white light-guide strip.
Technical reference: Based on Royalin-supplied installation photography for the pictured 2024–2026 Toyota Camry US-spec headlamp configuration. Verify the headlamp label, bracket points, projector dimensions and beam signals before ordering.
Related Headlight Retrofit Cases
Need This Camry US-Spec Retrofit Solution?
Send the vehicle year, headlamp label, housing, headlamp label, headlamp label, bracket orientation, projector thickness, connector and trim-clearance photos for matching.
Professional housing work, electrical testing, installation, sealing and beam aiming are recommended.
