BYD
Chery
Great Wall / Haval
Geely
MG
Toyota 86 / GT86 / Scion FR-S Projector Retrofit
A source-based reference for the pictured sports-coupe headlamp, covering the hot-melt-sealed housing, factory RX350 projector, replacement bracket and direct OEM xenon power connection.
86 / GT86 / FR-SProjector Bracket Application for the 86 / GT86 / FR-S
The supplied reference identifies one bracket solution for the pictured 2012–2015 Toyota 86 / GT86 and Scion FR-S headlamp family.
- Models
- Toyota 86 / GT86 / Scion FR-S
- Years
- 2012–2015 reference
- Sealant
- Factory hot-melt sealant
- OEM Projector
- RX350 unit shown
- Decoder
- Not required for factory xenon version
Article 1201 states that the OEM xenon version can use the original vehicle power without a decoder.
The source identifies the original projector as an RX350 unit.
An RX350 adapter may be used when required by the replacement configuration.
Hot-Melt Housing, RX350 Projector and Rear Mounting
Factory Hot-Melt Sealant
Use controlled heat and protect the sealing channel during opening and resealing.
Factory RX350 Projector
Retain reusable OEM components and use an RX350 adapter only when the replacement setup requires it.
Install from the Rear
Seat the completed bracket assembly into the rear housing and verify every mounting point.
Confirm the Xenon Headlamp Configuration
Reference Applies To
- 2012–2015 Toyota 86 / GT86 and Scion FR-S shown
- Matching vehicle-specific bracket points
- Factory RX350 projector configuration
- Factory hot-melt-sealed housing
- OEM xenon power connection verified
Not Automatically Confirmed
- Other model years or headlamp designs
- Halogen or aftermarket housings
- Unverified projector dimensions
- Direct power without connector and polarity verification
- RX350 adapter use without fitment confirmation
Send Photos for Verification
Provide the vehicle model, year, headlamp label, rear housing and projector photos.
86 / GT86 / FR-S Projector Installation Sequence
Confirm the Vehicle-Specific Bracket
Check bracket orientation, rubber grommets and supplied screws before disassembly.
Open the Hot-Melt-Sealed Housing
Heat and open the factory hot-melt-sealed headlamp while protecting the lens and sealing channel.
Remove the Factory RX350 Projector
Expose the original RX350 projector and retain reusable OEM components; prepare an RX350 adapter only if required.
Assemble the Replacement Projector
Mount the selected projector to the bracket and verify fastener seating and rear clearance.
Install the Bracket from the Rear
Position the completed bracket assembly into the rear of the headlamp housing and secure all mounting points.
Test and Reseal the Headlamp
Use the verified OEM xenon power connection, test beam operation and aim, then reseal the housing.
Detailed Installation Gallery
Match the Bracket and Projector as a Complete System
Vehicle-Specific Bracket
Confirm the 2012–2015 86 / GT86 / FR-S bracket, rubber grommets and fasteners.
Compatible Replacement Projector
Match projector body, mounting pattern, optical center and rear clearance.
Optional RX350 Adapter
Use an RX350 adapter only when the selected projector and mounting arrangement require it.
OEM Xenon Power Connection
Article 1201 states no decoder is required for the factory xenon version; verify connector and polarity.
Replacement Projector Installed in the OEM Housing
The completed reference shows the replacement projector secured behind the restored factory headlamp lens.
- Vehicle-specific bracket orientation confirmed
- Hot-melt-sealed housing opened and prepared
- Factory RX350 configuration identified
- Bracket assembly installed from the rear
- Power, beam aim and housing seal require final verification
Toyota 86 / GT86 / Scion FR-S Retrofit FAQ
Which vehicles are covered?
The supplied reference identifies the 2012–2015 Toyota 86 / GT86 and Scion FR-S headlamp configuration shown. Confirm the actual headlamp before ordering.
Does the factory xenon version need a decoder?
Article 1201 states that the factory xenon version does not require a decoder and can use the original vehicle power supply. Verify the connector and polarity first.
What sealant does the factory headlamp use?
The pictured factory headlamp uses hot-melt sealant. Controlled heating and careful channel preparation are required for opening and resealing.
Which original projector is shown?
The source identifies the factory projector as an RX350 unit.
Can an RX350 adapter be used?
Yes. The source notes that an RX350 adapter may also be used when needed, provided the projector and mounting arrangement match.
Technical reference: Based on Royalin-supplied installation photography and article 1201 for the pictured 2012–2015 headlamp configuration. Verify the exact model, headlamp label, projector and power connector before ordering.
Related Headlight Retrofit Cases
Need This 86 / GT86 / FR-S Retrofit Solution?
Send the model, year, headlamp photos, projector measurements and power connector for matching.
Professional headlamp opening, installation, resealing and beam aiming are recommended.