01 Hero · Model Y refresh two-option case

2025

Tesla Model Y Refresh Projector Retrofit

Single 3-Inch Square or Square + Inner Matrix

INSTALLATION REFERENCE

Choose a single 3-inch square projector, or add one inner matrix module with the accessory adapter. This reference covers these two configurations, not the separate full-matrix system.

◇ Refreshed Model Y ◇ Square 3-Inch Only ◇ Original Sources Retained

View Installation Guide

2025 Tesla Model Y refresh vehicle front lighting2025 Model Y Reference Lamp
02 Vehicle application

Model Y Two-Option Bracket Application

Models
Tesla Model Y Refresh
Years
2025
Headlamp
Pictured OEM Hella hard-cure-sealant lamp
Layout
One 3-inch square projector; optional one inner matrix module
Factory Parts
Original sources retained; original trim restored with local relief for the matrix option
Model Y square projector and optional matrix bracket kit
Square 3-Inch Only

Do not substitute a round 3-inch projector.

Optional Inner Matrix

Use the additional adapter only for this option.

Retained Sources

Use the specified wide-voltage harness.

03 Configuration options

One Main Carrier, Two Installation Routes

Option A: Single Square Projector

Step 01

Option A: Single Square Projector

Fit the main projector, then secure the intact supplied trim plate. The inner matrix accessory is not required.

Option B: Square + One Inner Matrix

Step 02

Option B: Square + One Inner Matrix

Install the accessory adapter, add the inner matrix module and modify the trim plate and OEM frame as illustrated.

04 Compatibility notice

Confirm the Configuration Before Trimming

Documented Configuration

  • 2025 refreshed Model Y reference lamp
  • 3-inch square main projector only
  • Optional one inner matrix module
  • Original sources retained with wide-voltage wiring

Not Automatically Confirmed

  • Previous Model Y lamp versions
  • Round main projector fitment
  • The separate full-matrix conversion
  • Unspecified inner module body dimensions

Request Matching

Send the lamp label and selected projector dimensions, and specify the single or combined route.

Request Verification

05 Shared preparation

Open the Lamp and Fit the Main Bracket

Open the Lens Cover

Step 01

Open the Lens Cover

The pictured OEM Hella lamp uses hard-cure sealant. Open the cover for the documented conversion.

Remove the OEM Projector

Step 02

Remove the OEM Projector

Remove the original projector assembly while retaining the original sources required by the supplier.

Install the Metal Bracket

Step 03

Install the Metal Bracket

Fit the main carrier at the illustrated housing mounting points.

05A Single-projector route

Front-Mount the Square Projector and Keep the Trim Plate Intact

Front-Mount the Projector

Step 01

Front-Mount the Projector

Install the 3-inch square projector in front of the main carrier.

Select the Recommended Shroud

Step 02

Select the Recommended Shroud

The photo recommends an E-type square shroud. Verify actual clearance before fitting.

Secure the Intact Trim Plate

Step 03

Secure the Intact Trim Plate

For the single-projector configuration, simply secure the trim plate without cutting out its center.

05B Optional matrix route

Install the Inner Adapter and Modify the Trim

Add the Inner Matrix Adapter

Step 01

Add the Inner Matrix Adapter

Use this accessory only when adding the inner matrix projector. The supplier permits fore/aft adjustment by changing spacing.

Cut the Supplied Trim Plate

Step 02

Cut the Supplied Trim Plate

Cut at the marked points and remove the center section for the combined configuration.

Install the Modified Trim Plate

Step 03

Install the Modified Trim Plate

Fit the modified plate around both optics, then check the OEM frame for the local interference shown in the next reference.

05C Matrix clearance

Relieve the Original Frame Locally

Model Y OEM frame local relief for the optional inner matrix

Trim the marked local OEM frame area only where it interferes with the inner matrix module. Adjust the module fore/aft spacing as needed and test-fit before final closure.

06 Electrical reference

Retain Original Sources and Match the Pictured Pin Numbering

Model Y low beam pins 7 and 6 high beam pins 5 and 6

Photo-Specific Circuit Definitions

  • Pin 7: low-beam positive
  • Pin 6: low-beam negative
  • Pin 5: high-beam positive
  • Pin 6: high-beam negative

The photo states that a common-negative wide-voltage harness may be used. Retain the original light sources. Verify the photographed numbering orientation on the actual board before connection.

07 Components to confirm

Match Your Selected Configuration

Main Square-Projector Carrier

Match the main bracket and housing mounting points.

Optional Matrix Adapter

Required only when adding one inner matrix module.

Trim Plate and Shroud

Single route keeps the plate intact; matrix route requires the illustrated cut.

Wide-Voltage Harness

Retain original sources; the pictured circuit permits common-negative wiring.

08 Installation reference

Single-Projector Completion and Combined-Route Clearance

Completed single square projector Model Y lampCombined square plus matrix local clearance reference

The supplied completed-lamp photograph documents the single-projector route. For the optional matrix route, check the illustrated frame clearance, beam functions and alignment before final closure.

09 Installation photographs

Detailed Model Y Installation References

10 Frequently asked questions

Tesla Model Y Refresh Retrofit FAQ

Which two configurations are covered?

The supplier covers a single 3-inch square projector, or a 3-inch square projector plus one inner matrix module. The separate full-matrix system is not covered here.

Can a round 3-inch projector be used?

No. The supplier specifies square 3-inch optics only.

When is the accessory adapter needed?

Only when adding the inner matrix module. It is not needed for a single square projector.

Does the supplied trim plate need cutting?

For the single-projector route, secure it intact. For the matrix route, cut at the marked points and remove the center section.

Can the inner module position be adjusted?

The supplier permits fore/aft adjustment using spacing. Check clearance and locally trim the marked OEM frame interference.

What electrical arrangement is required?

Retain the original sources and use a wide-voltage harness. The photo permits a common-negative harness and identifies pin 7 low positive, pin 5 high positive and pin 6 shared negative, in the pictured numbering orientation.

Technical reference: Supplier article 1099 and supplied installation photographs. Confirm lamp specification, square-projector fitment, optional matrix adapter, trim changes and photographed common-negative wiring.

Related Headlight Retrofit Cases

Match Your Model Y Brackets

Send the lamp label, inner and outer mounting positions and connector photographs for matching.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.