BYD
Chery
Great Wall / Haval
Geely
MG
Porsche Panamera Projector Retrofit
A structured retrofit reference for mid/low-spec Panamera headlights, covering the original assembly, wiring identification, bracket mounting and clearance checks.
Vehicle & Solution Overview
A compatibility snapshot for selecting the bracket, projector format and supporting electrical components before opening the headlight.
- Vehicle
- Porsche Panamera
- Model years
- 2017–2019
- Headlight
- Mid / low specification
- Application
- Adaptive and non-adaptive versions*
- Solution
- Projector mounting bracket
* Adaptive and non-adaptive units share the bracket according to the source case, but trimming requirements differ.
2017–2019 Porsche Panamera Retrofit Specifications
This reference documents the visible headlight configuration used for this projector upgrade. Confirm the exact headlight label and internal carrier before ordering parts.
- Vehicle
- 2017–2019 Porsche Panamera
- Headlight
- Mid/low-spec headlight configuration shown; adaptive and non-adaptive variants require verification
- Projector
- 3-inch square projector with compatible second-row mounting holes
- Bracket
- Application-specific Panamera projector mounting bracket
- Electrical
- OEM light source with a non-common-negative wide-voltage harness; verify polarity before connection
- Work scope
- Carrier trimming, retained lower mounting points, bracket installation, clearance checks, resealing and beam aiming
Before the Retrofit
Identify the original mounting points and serviceable parts before removing the projector assembly.
Original Headlight
Upper lens mounting holes are identified before disassembly.
Housing & Sealant
The source identifies OEM cold-glue sealant at the lens cover.
OEM Projector Assembly
Remove the original projector assembly carefully and retain reusable components.
Confirm the Configuration Before Ordering
Regional equipment and prior repairs can change the internal configuration. Use the points below as a pre-installation check.
Applies To
- 2017–2019 Porsche Panamera
- Mid / low-spec headlight assemblies shown
- Adaptive or non-adaptive version, subject to inspection
- 3-inch square projector with suitable second-row holes
Not Confirmed For
- Other Panamera model years or headlight specifications
- Round projector bodies
- Projectors without a usable second mounting-hole row unless professionally drilled
- Units with unverified previous modifications
Send Photos for Verification
Share the headlight label, front view, rear cover and the original projector mounting area. Royalin can help review the visible configuration before component selection.
Electrical Identification & Mounting Points
The supplied images identify left-side low-beam and right-side high-beam polarity. Always verify the vehicle and connector with appropriate test equipment before connecting components.
Left Side · Low Beam
Reference image marks the positive and negative terminals on the control board.
Right Side · High Beam
Reference image marks the positive and negative terminals on the control board.
Retain the Two Lower Mounting Holes
Cut away the surrounding original carrier as shown while preserving the two lower mounting points required by the bracket installation.
Primary Installation Sequence
The six primary stages below condense the supplied reference. Open any image to inspect its original annotation.
Open the Housing
Separate the lens cover while protecting the housing and internal trim.
Remove Trim Components
Carefully release the electroplated pieces and upper LED light cup.
Remove the OEM Projector
Remove the original lens and source while keeping the two lower holes.
Trim the Carrier
Cut along the indicated rear edge and preserve the required mounting structure.
Install the Bracket
Secure the application-specific bracket and confirm its seating at each retained point.
Reassemble & Check
Reinstall the OEM reflector. On adaptive units, test full movement for interference.
Detailed Installation Gallery
Components to Confirm as a System
Final selection depends on the exact headlight, projector hole pattern and market requirements. These are component categories, not unverified SKU claims.
Panamera Mounting Bracket
Application-specific bracket for the configuration shown.
Bracket Installed, Assembly Restored
The completed reference shows the projector assembly returned to the housing with the OEM upper reflector and exterior lens cover restored.
- Application-specific bracket seated on retained points
- OEM upper reflector reinstalled
- Second-row projector mounting holes used
- Decorative-panel interference area trimmed
- Adaptive movement check required where equipped
Porsche Panamera Projector Retrofit FAQ
Which Porsche Panamera models does this reference cover?
It covers the visible 2017–2019 Porsche Panamera mid/low-spec headlight configuration shown in this case. Regional equipment and previous repairs must be verified before ordering.
Does the bracket fit adaptive and non-adaptive headlights?
The supplied case states that the bracket is shared by adaptive and non-adaptive units, but trimming and movement-clearance requirements differ. Verify the exact headlight before installation.
Which projector format is used?
The case uses a 3-inch square projector with compatible second-row mounting holes and sufficient body clearance.
Can the original light source be retained?
The supplied reference specifies retaining the OEM light source and using a suitable non-common-negative wide-voltage harness. Test polarity and connector condition before connection.
Does the retrofit require professional installation?
Yes. Carrier trimming, electrical testing, adaptive-movement checks, resealing and beam aiming should be completed by an experienced automotive-lighting retrofit technician.
Technical source: supplied retrofit reference and installation images. Last reviewed by Royalin Lighting on August 29, 2026.
Related Porsche Retrofit Cases
Need This Panamera Retrofit Solution?
Send clear photos of the headlight label, housing and original projector. Royalin can help review the visible configuration and match suitable component options.
Compatibility may vary by regional model, headlight configuration and previous repair history. Verify before ordering. Professional installation, electrical testing, sealing and beam aiming are recommended.
REQUEST A BUSINESS SOLUTION
For retrofit shops, distributors and automotive lighting businesses.
We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.
Request Received!
Thank you for your business inquiry.
We've received your information and will review your request.
We'll get back to you within 1 business day.