01 Hero · Nissan Qashqai J11 Facelift projector case

2019–2022

Nissan Qashqai J11 Facelift Low-Beam Retrofit

Upgraded Koito / Xingyu Carrier · Xingyu Installation

INSTALLATION REFERENCE

Qashqai J11 upgraded low-beam carrier for Koito and Xingyu lamp variants, with Xingyu installation shown, Nissan decoding, OEM power use and local carrier/trim relief.

◇ Nissan Qashqai J11 Facelift ◇ Configuration-Specific Carrier

View Installation Guide

Nissan Qashqai J11 Facelift front headlampNissan Qashqai J11 Facelift Reference
02 Vehicle application

Nissan Qashqai J11 Facelift Application

Models
Nissan Qashqai J11 Facelift
Years
2019–2022
Headlamp
Pictured Koito or Xingyu original lamp; this installation shows Xingyu
Layout
Replacement outer low-beam projector; original inner high-beam unit retained
Factory Parts
Keep Xingyu plastic frame installed; restore high beam and original trim after local relief
Upgraded Koito / Xingyu Carrier · Xingyu Installation kit
Two Lamp Manufacturers

Early lamps are Koito; later lamps are Xingyu. Exterior appearance is the same but internals differ. Identify the actual housing code.

Upgraded Shared Carrier

The newer bracket adds Xingyu holes to the earlier Koito application. The older bracket is limited to the early Koito lamp.

Xingyu Frame Stays Installed

Perform the documented Xingyu conversion directly on the original plastic frame; it need not be removed.

03 Configuration details

Identify the Lamp and Prepare the Xingyu Carrier

Identify Xingyu by the Upper Housing Code

Step 01

Identify Xingyu by the Upper Housing Code

Use the model marking on the upper housing rather than external appearance or year alone.

Remove the Bent Bracket Leg for Xingyu

Step 02

Remove the Bent Bracket Leg for Xingyu

Cut off the illustrated bent leg for the documented Xingyu route.

Remove the Entire Marked Tab

Step 03

Remove the Entire Marked Tab

For Xingyu lamps, remove the full tab indicated in this separate detail.

04 Compatibility notice

Confirm the Lamp, Carrier and Module Selection

Documented Configuration

  • 2019–2022 Qashqai J11 facelift source application
  • Upgraded carrier with Koito and Xingyu mounting provisions
  • Detailed procedure shown specifically for Xingyu lamps
  • Nissan decoding and OEM power for conventional projectors

Do Not Assume

  • Identical outer appearance means identical lamp internals
  • The older Koito-only bracket also covers Xingyu lamps
  • Every Xingyu trimming step applies unchanged to Koito
  • The Xingyu plastic frame must be removed before conversion

Request Matching

Send lamp labels, module dimensions and the intended configuration.

Request Verification

05 Installation process

Installation Sequence

Identify and Open the Lamp

Step 01

Identify and Open the Lamp

The photo identifies OEM heat-softening sealant. Confirm the Xingyu housing code before following this procedure.

Remove the Trim Frame

Step 02

Remove the Trim Frame

Detach the decorative trim to reach the original projector.

Remove the OEM Projector Shroud

Step 03

Remove the OEM Projector Shroud

Carefully pry off the original shroud.

Remove the Original Projector

Step 04

Remove the Original Projector

Keep the original plastic mounting frame in the lamp for the documented Xingyu route.

Relieve Local Frame Interference

Step 05

Relieve Local Frame Interference

After removing the two indicated metal-bracket sections, trim only the marked interfering plastic areas.

Install the Metal Carrier

Step 06

Install the Metal Carrier

Secure the upgraded carrier at the illustrated mounting points.

Front-Mount the Replacement Projector

Step 07

Front-Mount the Replacement Projector

Mount the module in front of the metal bracket.

Fit the Recommended Type A Shroud

Step 08

Fit the Recommended Type A Shroud

Confirm the shroud clears the carrier and original trim.

Relieve Upper and Lower Trim

Step 09

Relieve Upper and Lower Trim

Trim the indicated upper and lower sections of the original trim frame to prevent interference.

Connect, Test and Complete

Step 10

Connect, Test and Complete

Use the matched Nissan decoder and verified power connections. Check low/high functions, warning behavior, aim and clearance before resealing.

06 Electrical reference

Follow This Configuration’s Electrical Requirements

Qashqai Xingyu original connector wiring
Xingyu reference: white/black low-beam positive, white negative, pink high-beam positive and gray decoder signal. Verify the actual circuit.

Supplier Instruction

Use the supplier-specified Nissan decoder. Conventional replacement projectors may connect directly to the original vehicle power according to the source. In the photographed Xingyu circuit, white/black is low-beam positive, white is negative, pink is high-beam positive and gray is decoder signal. The pictured Nissan/Mazda decoder uses red low-beam positive, black low-beam negative and yellow signal. Verify the actual lamp and connector before connection; do not transfer these definitions to Koito lamps without checking.

Test low/high switching, warning behavior and clearance during adjustment movement before final sealing.

07 Components to confirm

Match the Complete Kit

Upgraded Carrier Pair

Added Xingyu holes alongside the earlier Koito provisions.

Replacement Low-Beam Projector

Front mounting; conventional modules may use OEM power per source.

Original Plastic Frame and Trim

Xingyu frame stays installed; trim only illustrated interference areas.

Nissan Decoder and Type A Shroud

Matched decoding required; Type A decorative shroud recommended.

08 Installation result

Completed Nissan Qashqai J11 Facelift Headlamp

Nissan Qashqai J11 Facelift Low-Beam Retrofit completed

Confirm beam aim, electrical behavior, adjustment travel and cover clearance before final sealing.

09 Installation photographs

Detailed Installation References

10 Frequently asked questions

Nissan Qashqai J11 Facelift FAQ

Why identify the lamp manufacturer?

The source describes early Koito and later Xingyu lamps with identical outside appearance but different internals. Check the actual housing code rather than relying on year alone.

Does this upgraded carrier fit both?

The supplier says it adds Xingyu holes to the earlier Koito mounting provisions. The previous bracket was only for the early Koito lamps.

Which installation is shown here?

The Xingyu route. It includes Xingyu-specific bracket cuts and local frame relief; do not assume the Koito procedure is identical.

Must the original plastic frame come out?

No. The supplier states the Xingyu conversion can be performed directly on the plastic frame without removing it.

What electrical arrangement is required?

Use the specified Nissan decoder. Conventional replacement projectors may use original vehicle power according to the source; verify the actual lamp circuit.

What trim is modified?

For Xingyu, remove the indicated bent metal leg and whole tab, relieve marked plastic interference areas, and trim the upper/lower original trim frame. The photos recommend a Type A shroud.

Technical reference: Supplier article 829 and supplied installation photographs.

Related Headlight Retrofit Cases

Match Your Nissan Qashqai J11 Facelift Kit

Send your lamp label and intended projector configuration.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.