01 Hero · Nissan Kicks P15 Facelift projector case

2022–2023

Nissan Kicks P15 Facelift Three-Matrix Retrofit

Three 1.5–1.8 Inch Modules per Headlamp

INSTALLATION REFERENCE

Kicks P15 facelift triple-matrix conversion with three 1.5–1.8 inch modules per lamp, supplied spacer posts, clip assembly and trim-panel fastening. Decoding remains unconfirmed.

◇ Nissan Kicks P15 Facelift ◇ Configuration-Specific Carrier

View Installation Guide

Nissan Kicks P15 Facelift front headlampNissan Kicks P15 Facelift Reference
02 Vehicle application

Nissan Kicks P15 Facelift Application

Models
Nissan Kicks P15 Facelift
Years
2022–2023
Headlamp
Pictured pictured facelift headlamp; heat-softening sealant
Layout
Three matrix projectors per lamp, six across the pair
Factory Parts
Protect original wiring and restore sealed front cover after carrier installation
Three 1.5–1.8 Inch Modules per Headlamp kit
2022–2023 P15 Facelift

Match the pictured facelift lamp and carrier mounting.

Three Modules per Lamp

The supplier specifies a 1.5–1.8 inch mounting range, six modules across the pair.

Decoding Unconfirmed

Determine the actual electrical needs; the source does not yet confirm a decoder requirement.

03 Configuration details

Driver-Side Components and Spacer Assembly

Prepare Driver-Side Parts

Step 01

Prepare Driver-Side Parts

Remove the indicated accessory and match the main carrier, module mounts and trim panel.

Keep the Trim Fixing Available

Step 02

Keep the Trim Fixing Available

Leave the marked screw unsecured initially; it is fastened together with the trim panel later.

Install Clips and Spacer Guide Posts

Step 03

Install Clips and Spacer Guide Posts

Fit the blue clips and supplied spacer guide posts at the shown locations.

04 Compatibility notice

Confirm the Lamp, Carrier and Module Selection

Documented Configuration

  • 2022–2023 Nissan Kicks P15 facelift reference
  • Three 1.5–1.8 inch matrix projectors per lamp
  • Supplied spacer posts and illustrated clip arrangement
  • Trim-panel fixing completed after projector assembly

Do Not Assume

  • The decoder requirement is confirmed unnecessary
  • This kit has the earlier model’s 3-inch-square-only requirement
  • The marked trim fixing must be tightened before fitting the panel
  • The photo supplies a universal numbered pinout

Request Matching

Send lamp labels, module dimensions and the intended configuration.

Request Verification

05 Installation process

Installation Sequence

Identify the Original Lamp

Step 01

Identify the Original Lamp

The reference identifies OEM heat-softening sealant.

Open the Front Cover

Step 02

Open the Front Cover

Protect the original wiring, trim and lamp components.

Remove the Reflector Assembly

Step 03

Remove the Reflector Assembly

Detach the original optical assembly for replacement carrier installation.

Prepare Carrier Clips and Posts

Step 04

Prepare Carrier Clips and Posts

Match the supplied spacer locations and clip orientation. Keep the indicated trim screw available.

Install Three Matrix Modules

Step 05

Install Three Matrix Modules

Use the specified 1.5–1.8 inch mounting range and verify actual body clearance.

Secure the Trim Panel

Step 06

Secure the Trim Panel

Install the panel and complete its shared screw fastening after module assembly.

Install the Carrier in the Housing

Step 07

Install the Carrier in the Housing

Check carrier seating, fixings and wiring clearance.

Verify Electrical Needs and Finish

Step 08

Verify Electrical Needs and Finish

Determine actual decoding and power requirements, test low/high operation and warnings, set beam aim and restore the sealed cover.

06 Electrical reference

Follow This Configuration’s Electrical Requirements

Kicks facelift connector function reference
Connector photo labels high-beam positive, low-beam positive and negative. Decoding is not yet confirmed; verify actual circuits.

Supplier Instruction

The supplier explicitly states that whether decoding is needed remains to be confirmed and will be updated later. The connector photograph labels high-beam positive, low-beam positive and negative, but provides no confirmed numbered pins or universal wire-colour map. Verify actual circuit functions, suitable power wiring and warning behavior on the vehicle; do not assume another Nissan model’s decoder requirement.

Test low/high switching, warning behavior and clearance during adjustment movement before final sealing.

07 Components to confirm

Match the Complete Kit

Three-Position Carrier Pair

Match driver/passenger side and accessory assembly.

Matrix Modules

Three 1.5–1.8 inch projectors per headlamp.

Supplied Clips and Spacer Posts

Fit in the illustrated locations and orientation.

Trim Panel and Electrical Matching

Complete shared trim fixing; decoding remains to be confirmed.

08 Installation result

Completed Nissan Kicks P15 Facelift Headlamp

Nissan Kicks P15 Facelift Three-Matrix Retrofit completed

Confirm beam aim, electrical behavior, adjustment travel and cover clearance before final sealing.

09 Installation photographs

Detailed Installation References

10 Frequently asked questions

Nissan Kicks P15 Facelift FAQ

Which model is documented?

The 2022–2023 Nissan Kicks P15 facelift configuration shown.

How many modules fit?

Three per lamp, six across the pair, with the stated 1.5–1.8 inch mounting range.

Is decoding required?

The supplier has not confirmed this yet. Determine the actual vehicle’s electrical requirements and warning behavior before sealing.

What connector functions are shown?

High-beam positive, low-beam positive and negative. No numbered pins or universal colour map is provided.

Why leave one screw unsecured?

The assembly photo instructs leaving the indicated screw available so it can be fastened with the trim panel later.

Where do the spacer posts go?

At the locations marked in the carrier assembly detail, using the supplied posts and illustrated blue clip arrangement.

Technical reference: Supplier article 1660 and supplied installation photographs.

Related Headlight Retrofit Cases

Match Your Nissan Kicks P15 Facelift Kit

Send your lamp label and intended projector configuration.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.