01 Hero · W251 quad-projector case

2010–2017

Mercedes-Benz R-Class W251 Quad-Projector Retrofit

Low-Beam Carrier and High-Beam Conversion Brackets
INSTALLATION REFERENCE

A two-position reference covering the Bosch non-adaptive low-beam carrier, relocated high-beam mounting, projector alignment and final waterproof sealing.

◇ R-Class W251◇ Non-Adaptive Low-Beam Reference◇ Added High-Beam Projector

View Installation Guide

Completed Mercedes R Class W251 quad projector headlampW251 Quad-Projector Headlamp
02 Vehicle application

W251 Low- and High-Beam Bracket Application

The source documents a Bosch lamp with generally non-adaptive low beam. A top-spec adaptive lamp requires the appropriate Bosch adaptive bracket; do not substitute the illustrated non-adaptive carrier.

Models
Mercedes-Benz R-Class W251
Years
2010–2017 reference range
Headlamp
Bosch; heat-softening sealant
Layout
Non-adaptive low beam + added high-beam projector
Factory Parts
Low-beam clip and adjustment parts transferred
W251 high beam bracket pair
Both Position Kits Shown

Low-beam carrier replacement and high-beam relocation are separate operations.

Adaptive Version Needs Matching

The top-spec Bosch adaptive lamp requires its appropriate adaptive bracket.

Final Waterproof Sealing

Reseal the modified small housing opening after installation.

Position-Specific Bracket Sets

03 Critical mounting details

Clip Preparation and Relocated High-Beam Fixing

Side clip retaining barbs released

Original Side Clip

Snip the documented retaining barbs to release the clip. This alters the original retention; transfer it in the illustrated orientation.

Raised clip tab ground flat

Raised Tab Clearance

Grind the marked raised tab flat before fitting the replacement carrier.

High beam guide posts and silicone tubing

Guide Posts and Tubing

Fit the high-beam carrier with metal guide posts and approximately 10 mm silicone tubing as shown. The low-beam carrier has Hella Q5 mounting holes.

04 Compatibility notice

Verify Bosch Lamp Version and Projector Format

Documented Configuration

  • Pictured 2010–2017 R-Class W251 Bosch lamp
  • Non-adaptive low-beam carrier reference
  • Separate high-beam carrier and relocated mounting
  • Factory clip and adjustment parts transferred

Not Automatically Confirmed

  • Top-spec adaptive lamp with the non-adaptive carrier
  • Unverified projector dimensions or mounting patterns
  • Arbitrary mounting-foot cuts or plastic-tab removal
  • Masking tape used as final waterproof sealing

Request Matching

Send lamp label, adaptive status, original carrier and projector details.

Request Verification

05 Shared preparation

Open the Lamp and Remove Both Original Units

Open the Lamp and Remove Trim Screws

Step 01

Open the Lamp and Remove Trim Screws

The source identifies a Bosch lamp with heat-softening sealant. Remove the marked trim-frame screws with a T20 driver.

Remove the Low-Beam Assembly

Step 02

Remove the Low-Beam Assembly

Remove the low-beam bracket screws with a T20 driver, then withdraw the projector and carrier.

Remove the High-Beam Reflector

Step 03

Remove the High-Beam Reflector

Remove the original high-beam reflector to expose its mounting structure before relocation.

Selected Installation Details

05A Low-beam position

Non-Adaptive Low-Beam Carrier Replacement

Transfer Original Clip and Adjuster Parts

Step 01

Transfer Original Clip and Adjuster Parts

Transfer the illustrated original parts to the replacement plastic carrier. Snip the side-clip retaining barbs to release it and check the reinstallation orientation.

Install the Replacement Plastic Carrier

Step 02

Install the Replacement Plastic Carrier

Grind the illustrated raised tab flat and install the non-adaptive low-beam carrier with its transferred parts.

Prepare the Original Shroud

Step 03

Prepare the Original Shroud

Trim the marked original low-beam shroud points to fit the Hella projector. The replacement carrier provides Hella Q5 mounting holes for direct installation as shown.

05B High-beam position

High-Beam Mount Relocation and Projector Installation

Relocate the Obstructing Mount

Step 01

Relocate the Obstructing Mount

Cut the original square mount at its base. Its original position is too close to the projector center. Temporarily mask the opening to prepare for later sealing.

Install Clips and Guide Posts

Step 02

Install Clips and Guide Posts

Fit the raised clip with its metal shim. Remove only the illustrated plastic tabs beside the ball joint to prevent interference, then fit the carrier with metal guide posts and approximately 10 mm silicone tubing.

Fit and Align the High-Beam Projector

Step 03

Fit and Align the High-Beam Projector

Aim the low beam first, then adjust the added high-beam projector to match its pattern. Choose a suitable high-beam shroud and verify the documented H4-harness supply before final sealing.

Raised clip fitted with metal shim

Raised Clip and Shim

Secure and install the raised clip with the documented metal shim.

Plastic tab beside high beam ball joint removed

Local Plastic-Tab Removal

Remove the illustrated tabs beside the ball joint to prevent clip interference; follow both reference views.

High beam D series bulb and LED projector reference

Projector Format

The source shows D-series HID bulb and standard LED projector compatibility at the high-beam position. Verify the selected assembly and clearance.

06 Components to confirm

Both Carriers, Projectors, Harness and Sealant

Non-Adaptive Low-Beam Carrier

Match the Bosch non-adaptive replacement and transferred factory parts.

High-Beam Bracket Pair

Confirm the relocated fixing, clips, shim and guide posts.

Projectors and Shrouds

Check Q5 low-beam mounting and the selected high-beam projector format.

Harness and Sealing Supplies

Verify high-beam H4 supply and prepare proper final housing-opening sealant.

07 Result and final sealing

Align the Projectors and Reseal the Opening

Completed W251 quad projector lamp with H4 supply reference
Completed lamp; verify the documented high-beam H4-harness supply
Final housing opening sealing reference
Remove dust and seal the small opening; masking tape is temporary

The source recommends a dispenser with Japanese Yokohama sealant, or Kafuter 5905 silicone sealant as an alternative. Complete waterproof sealing after the mounting and alignment work.

08 Frequently asked questions

W251 Quad-Projector Retrofit FAQ

Which low-beam version is documented?

The source identifies a Bosch heat-softening-sealant lamp, generally with non-adaptive low beam. The illustrated low-beam replacement uses the Bosch non-adaptive carrier. A top-spec adaptive lamp requires the appropriate Bosch adaptive bracket and separate verification.

Why is the original high-beam fixing cut off?

The original fixing is too close to the projector center and obstructs installation. The procedure cuts the square mount at its base and relocates the mounting position using the documented ball-joint and clip arrangement.

Which parts are transferred to the low-beam carrier?

Transfer the illustrated original clip and adjustment components. The side clip is released after its retaining barbs are snipped, and its raised tab is ground flat as shown.

How is the high-beam carrier installed?

Install the illustrated raised clip and metal shim, remove the interfering plastic tabs and fit the carrier using metal guide posts with approximately 10 mm silicone tubing, as photographed.

How are the projectors aligned and powered?

First aim the low beam, then adjust the added high-beam projector to match the low-beam pattern. The source shows direct H4-harness supply to the high-beam position and notes D-series HID bulbs and standard LED projectors at that position. Verify the actual selected components and electrical setup.

How is the small housing opening finished?

Remove dust and reseal the opening after installation. The source recommends a sealant dispenser with Japanese Yokohama sealant, or Kafuter 5905 silicone sealant as an alternative. Masking tape is temporary preparation, not final waterproof sealing.

Technical reference: Supplied installation photography and article 95. Verify actual lamp version, projector mounting, electrical setup, alignment and sealing before installation.

Related Headlight Retrofit Cases

09 Business inquiry

Match Your W251 Retrofit Kit

Send lamp label, adaptive status and internal mounting photographs.

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.