01 Hero · W213 top-spec case

2016–2020

Mercedes-Benz E-Class W213 Top-Spec Projector Retrofit

Dedicated Top-Spec Projector Bracket Kit
INSTALLATION REFERENCE

A reference for the pictured top-spec lamp, covering original-shroud cutting and reuse, front-mounted replacement projectors and retained original light sources.

◇ E-Class W213◇ Top-Spec Reference◇ Separate-Negative Harness

View Installation Guide

Mercedes E Class W213 top spec vehicle headlampW213 Top-Spec Headlamp
02 Vehicle application

W213 Top-Spec Bracket Application

This dedicated top-spec procedure is distinct from the mid/low-spec quad-projector case. Match the pictured lamp internals and original shroud before choosing parts.

Models
Mercedes-Benz E-Class W213
Years
2016–2020 reference range
Headlamp
Top-spec Hella, hard-cure sealant
Layout
Front-mounted projector on replacement carrier
Factory Parts
Sources retained; cut outer shroud sections reused
W213 top spec bracket pair and clips
Dedicated Top-Spec Kit

Verify the actual lamp and bracket mounting arrangement.

Original Sources Retained

Use a separate-negative wide-voltage harness.

Original Shroud Reused

Cut the documented sections and refit the retained outer parts.

03 Critical preparation details

Shroud Cutting and Projector Clearance

Upper original shroud cutting line

Upper Cutting Guide

Cut the original shroud along the illustrated upper line and retain the outer section.

Lower original shroud cutting line

Lower Cutting Guide

Use the lower view to identify the matching cut. Do not extend cuts into unmarked mounting structure.

Projector mounting flange corner trimming

Mounting-Flange Corner

Trim only the marked projector mounting-flange corner for clearance, along with the illustrated local shroud areas.

04 Compatibility notice

Verify the Top-Spec Lamp Internals

Documented Configuration

  • Pictured 2016–2020 W213 top-spec lamp
  • Dedicated carrier and rear support parts
  • Front-mounted replacement projector
  • Original sources and outer shroud sections retained

Not Automatically Confirmed

  • Mid/low-spec quad-projector kit substitution
  • Every lamp based only on exterior appearance
  • H4 or connector pin assumptions from another version
  • Unmarked cutting or mounting modifications

Request Matching

Send lamp label, original shroud, mounting and connector photographs.

Request Verification

05 Installation process

Top-Spec Projector Installation Sequence

Open the Lamp and Remove Trim

Step 01

Open the Lamp and Remove Trim

The illustrated Hella lamp uses hard-cure sealant. Remove the front cover and decorative frame to expose the original projector assembly.

Disassemble the Original Unit

Step 02

Disassemble the Original Unit

Remove the original shroud and light source. Retain the original sources for the required electrical setup.

Cut and Retain the Outer Shroud

Step 03

Cut and Retain the Outer Shroud

Follow the illustrated upper and lower cut lines. Keep the outer section for refitting to the replacement bracket.

Front-Mount the Projector

Step 04

Front-Mount the Projector

Fit the rear support part to the main bracket, then front-mount and secure the replacement projector.

Trim and Secure the Shroud

Step 05

Trim and Secure the Shroud

Locally trim the marked projector flange corner and shroud areas. Secure the cut-off section and outer shroud directly at the documented points.

Fit the Assembly to the Rear Housing

Step 06

Fit the Assembly to the Rear Housing

Secure the bracket in the rear housing. Alternatively fit the bracket first, followed by the projector and shroud. Retain original sources and use the specified separate-negative harness.

Selected Installation Details

06 Components to confirm

Carrier, Projector, Original Parts and Harness

Top-Spec Bracket Pair

Match the main carriers, rear support parts and supplied clips.

Replacement Projector

Confirm front mounting and the marked flange-corner clearance.

Original Shroud Sections

Retain and refit the cut outer sections at the illustrated points.

Original Sources and Harness

Retain factory sources and use a separate-negative wide-voltage harness.

07 Assembly and result

Secure the Retained Shroud Sections

Rear support part fixed to main carrier

Rear Support Part

Secure the illustrated support part to the rear of the main carrier.

Cut off original shroud section secured

Cut-Off Section

Secure the retained cut-off shroud section directly as illustrated.

Outer shroud fastening points

Outer Shroud

Fasten the outer shroud at the three marked positions.

W213 top spec bracket fitted to rear housing
Bracket assembly secured to the rear housing
Completed W213 top spec projector installation
Completed top-spec headlamp reference
08 Frequently asked questions

W213 Top-Spec Retrofit FAQ

Which lamp is documented?

The reference identifies the pictured 2016–2020 Mercedes-Benz E-Class W213 top-spec headlamp. Match the actual lamp label and internal mounting structure before ordering.

Is this the mid/low-spec quad-projector kit?

No. This is a separate top-spec bracket reference with its own carrier and original-shroud cutting procedure. Do not substitute the mid/low-spec kit or its wiring definitions.

What wiring setup is required?

Retain the original light sources and use a separate-negative wide-voltage harness. The tutorial supplies no connector pinout; verify signals on the actual lamp rather than borrowing definitions from another version.

What happens to the original light source?

It is removed during mechanical disassembly but must be retained for the electrical setup as required by the supplier. Do not interpret its removal photograph as permission to discard it.

Which parts require trimming?

Cut the original shroud along the illustrated upper and lower lines and retain the outer section. Locally trim the marked projector mounting-flange corner and shroud interference areas as shown.

How is the assembly installed?

Front-mount and secure the projector, fasten the cut shroud section and outer shroud, then secure the bracket to the rear housing. The source also permits fitting the bracket first, followed by projector and decorative shroud.

Technical reference: Supplied installation photography and article 1708. Verify lamp configuration, cutting locations, mounting and electrical compatibility before installation.

Related Headlight Retrofit Cases

09 Business inquiry

Match Your W213 Top-Spec Kit

Send the actual lamp label and internal mounting photographs.

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.