01 Hero · CLS lower triple-matrix case

2015–2017

Mercedes-Benz CLS C218 Facelift Lower Triple-Matrix Retrofit

Lower High-Beam Position Conversion Kit
INSTALLATION REFERENCE

A reference for three matrix projectors in the lower high-beam position, with original-source retention, cornering-assist light transfer and a supplied carrier/baffle assembly.

◇ CLS C218 Facelift◇ Lower High-Beam Position◇ 1.5–1.7-Inch Recommended

View Installation Guide

Mercedes CLS C218 facelift vehicle front headlampCLS Facelift Lower-Position Reference
02 Vehicle application

CLS Lower High-Beam Triple-Matrix Application

The source uses three matrix projectors because outermost space is limited. Mounting holes cover 1.5–1.8-inch formats, but the recommended body size is 1.5–1.7 inches; confirm physical clearance separately.

Models
Mercedes-Benz CLS C218 Facelift
Years
2015–2017 reference range
Headlamp
Pictured lamp with lower LED reflector assembly
Layout
Three matrix projectors in the lower high-beam position
Factory Parts
Original sources and cornering-assist light retained
CLS lower high beam triple matrix bracket kit
Lower-Position Conversion

The carrier replaces the documented lower reflector assembly.

Space-Based Size Recommendation

Use 1.5–1.7-inch modules as recommended, not hole size alone.

Original Sources Retained

Use a separate-negative wide-voltage harness.

03 Carrier, reinforcement and spacing

Install the Supplied Fittings in Their Documented Positions

CLS carrier clips and fittings assembly

Clips and Fittings

Match the supplied clip and fitting arrangement to the carrier.

CLS carrier reinforcement fitting detail

Reinforcement Fitting

Install the illustrated reinforcement fitting at its marked location.

Supplied spacer at cornering assist light mounting

Supplied Spacer Post

Use the supplied spacer at the documented cornering-assist-light fixing point.

04 Compatibility notice

Confirm Lower-Position Space and Module Dimensions

Documented Configuration

  • Pictured 2015–2017 CLS C218 facelift lamp
  • Lower high-beam reflector conversion
  • Three matrix projectors per headlamp
  • Original sources and cornering-assist light retained

Not Automatically Confirmed

  • Upper-position or other lamp-version conversions
  • Every 1.8-inch body based on mounting holes alone
  • Unverified connector pin assignments
  • OEM adaptive matrix-control functionality

Request Matching

Send lamp label, lower reflector and selected projector/module dimensions.

Request Verification

05 Installation process

Lower Triple-Matrix Installation Sequence

Open the Front Cover

Step 01

Open the Front Cover

Remove the front cover while protecting the housing, original optical units and sealing channel. The tutorial does not specify a sealant type.

Remove the Decorative Frame

Step 02

Remove the Decorative Frame

Remove the illustrated lower decorative frame to expose the lower reflector assembly.

Remove the Lower LED Reflector Assembly

Step 03

Remove the Lower LED Reflector Assembly

Remove the original lower LED reflector assembly while retaining the original light sources for the specified electrical setup.

Transfer the Cornering-Assist Light

Step 04

Transfer the Cornering-Assist Light

Install the original cornering-assist light onto the replacement carrier, using the supplied spacer post at the illustrated location.

Install Three Matrix Projectors

Step 05

Install Three Matrix Projectors

Fit three lower-position projectors. Although 1.5–1.8-inch hole patterns are provided, use the recommended 1.5–1.7-inch format unless actual clearance is separately verified.

Install the Carrier and Baffle Plate

Step 06

Install the Carrier and Baffle Plate

Match the documented clips and reinforcement fitting, then install the assembled carrier and baffle plate. Retain original sources and verify the separate-negative harness before final assembly.

Selected Installation Details

06 Components to confirm

Carrier, Matrix Modules, Original Light and Harness

Lower Triple-Matrix Carrier

Match the supplied clips, reinforcement fitting and baffle plate.

Three Matrix Projectors per Lamp

1.5–1.7-inch units recommended because of space constraints.

Original Cornering-Assist Light

Transfer the original unit using the supplied spacer at the marked point.

Original Sources and Harness

Retain factory sources and use a separate-negative wide-voltage harness.

07 Assembly details and result

Restore the Cornering Light and Complete the Lower Array

CLS assembled clips and lower carrier reference

Assembled Carrier Reference

Compare clip and support orientation against the supplied assembly view.

Original cornering assist light installed on replacement carrier

Cornering-Assist Light

Transfer the original light onto the replacement assembly as illustrated.

Triple matrix projector size recommendation

Three-Projector Array

The supplier recommends 1.5–1.7-inch projectors for the available space.

CLS lower triple matrix carrier and baffle installed
Lower carrier and baffle installed
Completed CLS facelift lower triple matrix retrofit
Completed headlamp installation reference
08 Frequently asked questions

CLS Lower Triple-Matrix Retrofit FAQ

Which part of the lamp is converted?

The source describes the lower high-beam position of the pictured 2015–2017 CLS facelift lamp, replacing its lower LED reflector assembly with three matrix projectors.

Why does the kit use three matrix projectors?

The supplier notes limited space at the outermost position and substantial obstruction with a separate high-beam unit, so this reference uses three matrix projectors instead.

Which projector size is recommended?

The carrier includes hole patterns for 1.5–1.8-inch modules, but the supplier recommends 1.5–1.7-inch projectors because of the available space. Hole compatibility is not a guarantee that every 1.8-inch body fits.

What electrical setup is required?

Retain the original light sources and use a separate-negative wide-voltage harness. This tutorial does not provide a confirmed connector pinout; verify signals on the actual lamp.

What happens to the cornering-assist light?

Transfer and install the original cornering-assist light on the replacement assembly as illustrated, using the supplied spacer post at the documented fixing.

What finishing parts are installed?

Install the supplied clips and reinforcement fitting, then fit the three projectors, carrier and baffle plate. Verify the actual mechanical and electrical setup; the term matrix here does not establish an OEM adaptive-control upgrade.

Technical reference: Supplied installation photography and article 1202. Verify actual lamp, module dimensions, cornering-light mounting, source retention and electrical compatibility before installation.

Related Headlight Retrofit Cases

09 Business inquiry

Match Your CLS Lower Triple-Matrix Kit

Send the actual lower reflector and selected matrix-projector dimensions.

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.