Lexus GS Five-Matrix Projector Retrofit
Five Matrix Modules per Headlamp
INSTALLATION REFERENCE
Lexus GS five-matrix retrofit with 1.5–1.7 inch modules recommended, 1.8 inch mounting holes, raised plastic guide post, transferred leveling motor and retained OEM source.
Lexus GS Five-Matrix ReferenceGS Five-Matrix Application
- Models
- Lexus GS
- Years
- 2016–2020
- Headlamp
- Pictured OEM GS headlamp with butyl sealant
- Layout
- Five matrix projectors per lamp; 1.5–1.7 inch recommended with 1.8 inch mounting holes provided
- Factory Parts
- Retain original source; transfer motor and clip; raise plastic guide post and restore trim panel

Ten replacement matrix modules across the pair.
Use 1.5–1.7 inch modules as recommended. The bracket also has 1.8 inch holes; verify actual body clearance.
Use separate-negative wide-voltage wiring.
Prepare the Driver-Side Carrier and Mounting Points
Identify Driver-Side Components
Match the main carrier, module plates, motor support and decorative panel.
Install the Blue Clip
Fit the blue clip at the illustrated carrier position.
Raise the Plastic Guide Post
Use a spacer at the highlighted plastic guide-post location as shown.
Confirm the Lamp, Carrier and Module Selection
Documented Configuration
- 2016–2020 Lexus GS reference lamp
- Five matrix modules per headlamp
- 1.5–1.7 inch modules recommended; 1.8 inch hole patterns included
- Retained original source and separate-negative wide-voltage harness
Do Not Assume
- All 1.8 inch projector bodies are confirmed by hole fit alone
- The guide-post spacer can be omitted
- Motor support screw order is arbitrary
- A fixed electrical pinout is supplied
Request Matching
Send lamp labels, module dimensions and the intended configuration.
Installation Sequence
Identify and Open the Original Lamp
The photo identifies OEM butyl sealant.
Remove the Front Cover
Open the lamp and protect retained parts.
Remove the Original Light Modules
Remove the optical assembly for access while retaining the original light source required by the wiring arrangement.
Assemble the Carrier Plates
Follow the illustrated driver-side component arrangement.
Transfer the OEM Clip
Fit the original clip at the highlighted carrier location.
Fit Five Modules and the Leveling Motor
Install the chosen modules and the original self-leveling motor at the illustrated lower support.
Start the Motor-Bracket Screw First
Install the highlighted motor-support screw before continuing with panel assembly.
Install the Trim Panel
Secure the trim panel along the indicated fixing points.
Inspect the Completed Panel Assembly
Check panel seating and clearance around all five modules.
Install the Carrier in the Rear Housing
Seat and secure the completed assembly; check movement, beam aim, low/high operation and cover clearance before sealing.
Follow This Configuration’s Electrical Requirements

Supplier Instruction
Retain the original light source and use a wide-voltage harness with separate, non-common negative circuits. The photograph identifies high-beam and low-beam signal connections at the original source assembly. It does not provide a universal numbered pinout, every signal polarity or a separate decoding instruction. Verify the actual connections.
Test low/high switching, warning behavior and clearance during adjustment movement before final sealing.
Match the Complete Kit
Five-Position Carrier
Match driver/passenger-side parts and stepped module plates.
Matrix Modules
1.5–1.7 inch recommended; body clearance still governs 1.8 inch options.
Guide Post, Clips and Motor
Raise the marked plastic post, transfer the OEM clip and follow motor screw order.
Retained Source and Harness
Use separate-negative wide-voltage wiring.
Completed Lexus GS Matrix Headlamp

Confirm beam aim, electrical behavior, adjustment travel and cover clearance before final sealing.
Lexus GS Five-Matrix FAQ
How many modules fit?
Five per headlamp, ten across the pair.
Which module size is recommended?
The supplier recommends 1.5–1.7 inch modules and notes that 1.8 inch mounting holes are included. Check actual module body clearance.
Which electrical arrangement is required?
Retain the original light source and use a wide-voltage harness with separate negative circuits.
What happens at the plastic guide post?
Raise the highlighted guide post with the illustrated spacer.
What motor installation order is shown?
Install the highlighted motor-bracket screw first, then continue fitting the trim panel at the marked points.
What should be checked before sealing?
Confirm guide-post height, clip seating, motor operation, panel clearance, beam aim and low/high switching.
Technical reference: Supplier article 1639 and supplied installation photographs.
Related Headlight Retrofit Cases
Match Your Lexus GS Five-Matrix Kit
Send your lamp label and intended projector configuration.









