01 Hero · Shared JETOUR base-spec case

2022–2023

JETOUR X90 / X90 PLUS / X95 Projector + Matrix Retrofit

One 3-Inch Projector plus One Matrix per Lamp

INSTALLATION REFERENCE

A shared bracket application for the documented base-spec lamps of three JETOUR models. Each lamp accepts a 3-inch projector and a 1.5–1.8 inch matrix module. The supplier specifies no decoding and recommends a separate wiring harness.

◇ Three Model Applications ◇ Base-Spec Lamps ◇ 3-Inch + Matrix

View Installation Guide

JETOUR reference vehicle front headlampShared Base-Spec Lamp Reference
02 Vehicle application

Shared Bracket for X90, X90 PLUS and X95

Models
JETOUR X90 / X90 PLUS / X95
Years
2022–2023 supplier reference range
Headlamp
Documented base-spec lamp; factory hard-cure sealant
Layout
One 3-inch projector plus one 1.5–1.8 inch matrix in each lamp
Factory Parts
Local clearance depends on projector body; restore DRL cover and surrounding trim
Shared JETOUR 3-inch and matrix bracket pair
Three Listed Models

Match the pictured base-spec internals for X90, X90 PLUS or X95.

Paired Optical Modules

Verify both the 3-inch body and matrix-module clearance.

Harness Recommended

No decoding is specified; the supplier recommends a wiring harness.

03 Optical configuration

Match the Two Modules and Their Clearance

Prepare the Shared Carrier

Step 01

Prepare the Shared Carrier

Install the illustrated white clips in their photographed positions.

Front-Mount the Projectors

Step 02

Front-Mount the Projectors

Mount the projectors in front of the bracket. The photo shows short-body matrix clearance; with 1.7–1.8 inch modules, locally relieve the indicated edge of the 3-inch projector if it interferes.

A round 3-inch projector has tight upper clearance and requires local grinding. The supplier describes a flat projector as the easier fit; test the actual body and trim before final assembly.

04 Compatibility notice

Verify Base-Spec Internals on Each Model

Documented Applications

  • 2022–2023 JETOUR X90 base-spec lamp
  • 2022–2023 JETOUR X90 PLUS base-spec lamp
  • 2022–2023 JETOUR X95 base-spec lamp
  • One 3-inch and one 1.5–1.8 inch matrix per lamp

Do Not Assume

  • Every trim or regional lamp is identical
  • High-spec LED lamps use this bracket
  • All round projectors clear the upper trim unchanged
  • Large matrix bodies need no adjacent-projector relief

Request Matching

Send the model, year, lamp label, internal mounting points and both module dimensions.

Request Verification

05 Installation process

Install the 3-Inch and Matrix Assembly Together

Remove the Front Cover

Step 01

Remove the Front Cover

Open the factory hard-cure-sealant lamp and protect the retained components.

Remove the Factory Projector

Step 02

Remove the Factory Projector

Remove the original optical assembly and trim to expose the mounting points.

Install the Carrier Clips

Step 03

Install the Carrier Clips

Match the white clips to the supplied bracket detail.

Fit Both Replacement Modules

Step 04

Fit Both Replacement Modules

Front-mount the 3-inch and matrix modules; check their mutual clearance before tightening.

Seat the Assembly in the Housing

Step 05

Seat the Assembly in the Housing

Install the prepared carrier and verify both module positions.

Fit the Lower Trim Plate

Step 06

Fit the Lower Trim Plate

Install the illustrated lower trim plate. The supplied photo recommends a Type A shroud.

05A DRL-cover clearance

Remove the DRL Cover Before Relieving Interference

Check the DRL Cover Against the Projector

Step 01

Check the DRL Cover Against the Projector

Remove the DRL cover from the trim frame and locally relieve the marked area for projector clearance. The reference says this cut is not needed with a flat projector.

Restore the Cover After Trimming

Step 02

Restore the Cover After Trimming

Reinstall the cover and check its clearance before restoring the complete trim assembly.

06 Electrical reference

No Decoding; Wiring Harness Recommended

JETOUR low positive high positive and three left ground wires
The photograph identifies low-beam positive and high-beam positive. It labels all three wires on the left, in the photographed orientation, as ground. No numbered universal pinout is supplied.

No Decoder Required

The supplier specifies no decoding for this documented base-spec configuration.

Harness Recommended

Use the supplier-recommended separate harness and verify low/high beam operation of both replacement modules.

07 Components to confirm

Match Both Optical Modules and the Carrier

Shared Carrier and Clips

Match the actual base-spec lamp internals.

3-Inch Projector

Check upper clearance, especially with round bodies.

1.5–1.8 Inch Matrix

Verify body length and clearance beside the 3-inch projector.

Harness, Plate and Shroud

Provide the recommended harness and fit the illustrated lower plate; Type A is recommended.

08 Installation result

Completed Projector + Matrix Reference

Completed JETOUR base-spec 3-inch and matrix retrofit

Check both module functions, beam aim, DRL, trim clearance and sealing before vehicle installation.

09 Installation photographs

Shared JETOUR Installation Details

10 Frequently asked questions

X90 / X90 PLUS / X95 Retrofit FAQ

Which models are listed?

The supplier lists 2022–2023 JETOUR X90, X90 PLUS and X95 base-spec lamps. Match the actual lamp internals and mounting points for each vehicle.

Which modules fit each lamp?

The source specifies one 3-inch projector plus one 1.5–1.8 inch matrix module per lamp.

Does a round 3-inch projector need relief?

The supplier says its upper space is tight and requires local grinding. The DRL-cover photo notes that its illustrated cut is unnecessary with a flat projector.

What changes with larger matrix bodies?

The photo calls for local relief of the adjacent 3-inch projector edge when fitting 1.7–1.8 inch matrix modules if needed to avoid interference.

Is decoding required?

No decoding is specified. The supplier recommends a separate wiring harness.

Which shroud is recommended?

The installation photograph recommends Type A and shows a lower trim plate. Verify actual projector and trim clearance before sealing.

Technical reference: Supplier article 718 and supplied installation photographs. Confirm base-spec model application, both module dimensions, front mounting and DRL-cover clearance.

Related Headlight Retrofit Cases

Match Your Shared JETOUR Bracket

Send model, year, lamp labels and projector dimensions for matching.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.