01 Hero · X70L lower-position case

2026

JETOUR X70L Lower-Position Projector Retrofit

3-Inch Square Projector with External Vertical Adjustment

INSTALLATION REFERENCE

Replace the lower auxiliary reflector with a 3-inch square projector using the ball-joint carrier. The completed lower assembly can be adjusted vertically from outside the housing. Follow the side-specific clip holes, housing relief and adjustment-screw preparation.

◇ Lower Position Only ◇ 3-Inch Square Only ◇ Independent Vertical Aim

View Installation Guide

2026 X70L upper main and lower auxiliary lamp positions2026 Lower-Position Reference
02 Vehicle application

X70L Lower Adjustable Bracket Application

Models
JETOUR X70L
Years
2026
Headlamp
Pictured factory hard-cure-sealant lamp
Layout
Lower auxiliary reflector replaced by an adjustable square projector
Factory Parts
Local heat-sink and housing relief; restore DRL and surrounding trim
X70L lower bracket clips ball joints and adjustment hardware
Square Projector Only

The supplier specifies a 3-inch square module.

External Vertical Adjustment

The lower assembly can be aimed vertically after installation.

No Decoder

Check flash-to-pass when using factory power, and confirm the required lower-only wire joining.

03 Bracket orientation

Shared Brackets with Side-Specific Clip Holes

Match the Clip Orientation

Step 01

Match the Clip Orientation

The bracket bodies are interchangeable left/right, but driver- and passenger-side clip holes differ. Follow the illustrated holes and do not reverse the clips.

Fit the Lower Projector Bracket

Step 02

Fit the Lower Projector Bracket

Install the lower bracket in the photographed direction and select the side-appropriate lower clip hole.

04 Compatibility notice

Confirm Lower-Position Geometry and Adjustment

Documented Configuration

  • 2026 X70L lower-position conversion
  • 3-inch square projector only
  • Ball-joint carrier and supplied adjustment screw
  • Independent vertical adjustment after installation

Do Not Assume

  • Round projectors fit this carrier
  • The upper-position kit follows this procedure
  • Left/right clip holes are identical
  • The general connector photo specifies the wire-joining pairs

Request Matching

Send lamp labels, lower mounting details, connector photographs and square-projector dimensions.

Request Verification

05A Housing preparation

Prepare the Lower Housing and External Adjuster

Open the Front Cover

Step 01

Open the Front Cover

Open the factory hard-cure-sealant lamp to reach the lower optical assembly.

Remove the Outer Trim Frame

Step 02

Remove the Outer Trim Frame

Remove the surrounding frame and preserve retained components.

Remove the Lower Reflector

Step 03

Remove the Lower Reflector

Remove the factory lower auxiliary reflector; the upper projector is outside this conversion.

Relieve the Heat-Sink Area

Step 04

Relieve the Heat-Sink Area

Heat and push back the indicated housing detail, and locally trim the marked aluminum heat-sink section.

Prepare the Adjustment Hole

Step 05

Prepare the Adjustment Hole

Remove the cable-tie base and drill through the indicated location using a 4 mm bit.

Install the Supplied Ball-Head Screw

Step 06

Install the Supplied Ball-Head Screw

Fit the supplied screw through the prepared adjustment location.

05B Carrier and projector installation

Install the Ball-Joint Carrier in the Correct Direction

Check the Heat-Sink-Side Relief

Step 01

Check the Heat-Sink-Side Relief

Compare the trimmed local section with the detail and ensure the carrier has clearance.

Relieve the Remaining Housing Interference

Step 02

Relieve the Remaining Housing Interference

Heat and push down the marked area and remove the two indicated lower screw bosses.

Install the Housing Carrier

Step 03

Install the Housing Carrier

Fit the illustrated carrier in the correct direction; do not reverse it.

Fit Two Upper Plastic Ball Studs

Step 04

Fit Two Upper Plastic Ball Studs

Secure the two supplied plastic ball studs at the top of the square projector.

Attach the Lower Projector Bracket

Step 05

Attach the Lower Projector Bracket

Match bracket orientation and the correct clip hole for the lamp side.

Snap the Projector onto the Carrier

Step 06

Snap the Projector onto the Carrier

Seat the prepared projector on the rear-housing ball-joint mounting arrangement.

05C Shroud and trim clearance

Test-Fit Before Local Trimming

Choose a Suitable Shroud

Step 01

Choose a Suitable Shroud

The photo illustrates Type E. Confirm clearance with the actual projector.

Check the Upper Interference Area

Step 02

Check the Upper Interference Area

Relieve only the marked local trim interference beside the lower assembly.

Check the Side Interference Area

Step 03

Check the Side Interference Area

Test-fit the frame and trim the indicated local area where necessary.

Match Clearance to the Projector

Step 04

Match Clearance to the Projector

The source explicitly makes this additional relief dependent on the installed projector.

Restore the Trim Frame

Step 05

Restore the Trim Frame

Reinstall the surrounding frame and check clearance through the adjustment range.

Adjust the Lower Vertical Aim

Step 06

Adjust the Lower Vertical Aim

The photographed external screw provides independent vertical adjustment after assembly.

06 Electrical reference

No Decoding; Verify Passing-Light and Wire-Joining Details

X70L connector low positive high positive and two grounds
The photo labels low-beam positive, high-beam positive and two grounds. Match the actual connector orientation; no numbered universal pinout is supplied.

Check Flash-to-Pass

The supplier states no decoding is required but directs checking flash-to-pass when connecting a conventional projector to factory power.

Lower-Only Wire Joining

The text says a lower-only conversion requires joining wires for the lower source to illuminate. This photo set does not identify the specific joining pairs. Confirm that detail with the supplier before connection.

07 Components to confirm

Match the Adjustable Lower Kit

Lower Carrier

Check bracket direction and side-specific clip holes.

3-Inch Square Projector

Prepare the two upper plastic ball studs.

Adjustment Screw and Joints

Fit the supplied ball-head screw at the 4 mm drilled location.

Shroud and Trim

Test-fit Type E or another suitable shroud and relieve local interference.

08 Installation result

Completed Lower-Position Headlamp

Completed 2026 X70L adjustable lower projector retrofit

Confirm electrical operation, flash-to-pass, DRL, lower vertical adjustment and beam aim before final sealing.

09 Installation photographs

X70L Lower-Position Details

10 Frequently asked questions

X70L Lower-Position Retrofit FAQ

Which position is converted?

This procedure replaces the lower auxiliary reflector. The upper projector has a separate bracket and installation reference.

Which projector fits?

The supplier specifies 3-inch square projectors only.

Can the lower beam be adjusted after installation?

Yes. The completed bracket provides external, independent vertical adjustment using the supplied adjustment arrangement.

Are the brackets side-specific?

The bracket bodies can be used on either side, but the photo specifies different clip holes for driver and passenger sides. Do not reverse the bracket or clips.

What drilling and relief are documented?

Remove the cable-tie base, drill the marked point with a 4 mm bit, install the supplied ball-head screw and follow the photographed local housing, heat-sink and trim relief.

What electrical details need checking?

No decoding is specified, but flash-to-pass must be tested on factory power. The text requires wire joining for a lower-only conversion without identifying the joining pairs in these photos; confirm the exact detail with the supplier.

Technical reference: Supplier article 1415 and supplied photographs. Match lower-carrier direction, clip holes, ball joints, adjustment screw and local clearance work.

Related Headlight Retrofit Cases

Match Your X70L Lower Bracket

Send lamp labels, lower mounting points and square-projector dimensions for matching.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.