01 Hero · XTS non-adaptive case

2013–2017

Cadillac XTS Non-Adaptive Rear-Access Projector Retrofit

Factory Xenon to LED · Front Cover Retained

INSTALLATION REFERENCE

XTS non-adaptive xenon-to-LED rear-access retrofit: decoding required, side-specific bent lower bracket, original clip transfer, plastic/metal lower carrier differences and rear installation sequence.

◇ CT5 Facelift ◇ Configuration-Specific Carrier

View Installation Guide

Cadillac XTS front headlampXTS Non-Adaptive Reference
02 Vehicle application

XTS Non-Adaptive Application

Models
Cadillac XTS non-adaptive
Years
2013–2017
Headlamp
Pictured OEM Bosch xenon cold-sealant headlamp
Layout
Non-adaptive projector replacement through rear access with a multi-part replacement carrier
Factory Parts
Transfer original clips and lower support parts; retain front cover and restore rear access cover
Factory Xenon to LED · Front Cover Retained kit
Non-Adaptive Version

For the documented 2013–2017 XTS non-AFS xenon headlamp.

Decoding Required for LED

The supplier explicitly requires decoding for the xenon-to-LED conversion.

One Side-Specific Component

Only the bent bracket component is left/right specific; follow the illustrated assembly orientation.

03 Configuration details

Identify the Carrier and Original Lower Support

Review the Front Assembly

Step 01

Review the Front Assembly

Match the main ring, upper fixing strip and bent lower component to the reference.

Review the Rear Assembly

Step 02

Review the Rear Assembly

Follow the illustrated carrier and clip relationship during assembly.

Identify Plastic or Metal Lower Support

Step 03

Identify Plastic or Metal Lower Support

The original lower support may be plastic or metal. The photo cautions that the plastic version is fragile; the metal type can be removed directly.

04 Compatibility notice

Confirm the Lamp, Carrier and Module Selection

Documented Configuration

  • 2013–2017 XTS non-adaptive xenon reference lamp
  • Rear-access replacement with front cover retained
  • Decoding for xenon-to-LED conversion
  • Correct left/right bent lower component

Do Not Assume

  • This procedure confirms adaptive/AFS fitment
  • All bracket components are left/right specific
  • The fragile plastic lower support can be treated like metal
  • The illustrative small rear opening must always be cut

Request Matching

Send lamp labels, module dimensions and the intended configuration.

Request Verification

05 Installation process

Installation Sequence

Identify the OEM Headlamp

Step 01

Identify the OEM Headlamp

The photo identifies an OEM Bosch cold-sealant headlamp.

Remove the Projector Through Rear Access

Step 02

Remove the Projector Through Rear Access

Remove projector screws and the top cover, then withdraw the original projector as illustrated.

Release the Lower Support Carefully

Step 03

Release the Lower Support Carefully

Remove the highlighted screw and clip the marked connecting sections only as illustrated for the plastic lower support. Protect nearby wiring and the fragile original parts.

Prepare Rear Screw Access

Step 04

Prepare Rear Screw Access

The photo shows removing the indicated mounting tab/head to improve access for the rear screw.

Release the OEM Retaining Clip

Step 05

Release the OEM Retaining Clip

Push up the cover with a screwdriver to release the original clip.

Avoid an Unnecessary Rear Cut

Step 06

Avoid an Unnecessary Rear Cut

The small opening shown was cut for visibility. Normally pry the clip free; local cutting is an alternative only if it cannot be released.

Transfer the Original Clip

Step 07

Transfer the Original Clip

Remove the original clip and install it on the replacement upper component.

Reinstall the Upper Component

Step 08

Reinstall the Upper Component

Place the transferred clip and fixing component back into the lamp.

Fit the Main Carrier Loosely

Step 09

Fit the Main Carrier Loosely

Insert the main mounting bracket and start the top two screws without fully tightening.

Prepare the Bent Lower Bracket

Step 10

Prepare the Bent Lower Bracket

Transfer the original lower parts to the correct left/right bent component; do not reverse it.

Fit and Tighten the Lower Assembly

Step 11

Fit and Tighten the Lower Assembly

Insert the lower component and secure the lower screws.

Insert the Replacement Projector

Step 12

Insert the Replacement Projector

Insert the projector from the side through the rear access and secure it directly. Verify carrier seating and adjustment before completion.

Inspect the Front Result

Step 13

Inspect the Front Result

Check alignment, low/high operation and decoding behavior before restoring the rear cover.

06 Electrical reference

Follow This Configuration’s Electrical Requirements

XTS replacement projector rear installation
Mechanical rear-installation reference: insert the projector from the side and secure it. A wiring pinout is not provided.

Supplier Instruction

The supplier states that converting the original xenon headlamp to LED requires decoding. The source does not provide a universal numbered pinout, harness type or separate OEM light-source-retention instruction. Match the decoding arrangement to the actual projector and vehicle.

Test low/high switching, warning behavior and clearance during adjustment movement before final sealing.

07 Components to confirm

Match the Complete Kit

Multi-Part Carrier

Follow front/rear assembly reference and loose upper-first sequence.

Bent Lower Component

Left/right specific; transfer the original lower parts.

Original Retaining Clip

Release carefully and transfer to the replacement upper strip.

LED Projector and Decoding

Original xenon-to-LED conversion requires decoding.

08 Installation result

Completed XTS Projector Installation

Cadillac XTS Non-Adaptive Rear-Access Projector Retrofit completed

Confirm beam aim, electrical behavior, adjustment travel and cover clearance before final sealing.

09 Installation photographs

Detailed Installation References

10 Frequently asked questions

XTS Non-Adaptive FAQ

Which XTS headlamp is covered?

The documented 2013–2017 non-adaptive/non-AFS xenon headlamp, with an OEM Bosch reference lamp.

Is decoding required?

Yes. The supplier requires decoding when converting the original xenon lamp to LED.

Which bracket component differs left to right?

Only the bent component is side-specific; the other supplied components are not left/right specific, but their assembly orientation still matters.

Why identify the original lower support material?

The support may be plastic or metal. The photo warns that the plastic version is fragile and needs careful removal.

Must the small rear clip-access opening be cut?

No. The photo says it was cut for a clearer view; normally pry the clip free. Local cutting is an alternative only if it cannot be released.

What is the installation order?

Transfer the original clip, fit the upper component, start the top screws loosely, install the correct bent lower component, then secure the carrier and insert the projector from the side.

Technical reference: Supplier article 505 and supplied installation photographs.

Related Headlight Retrofit Cases

Match Your XTS Non-Adaptive Kit

Send your lamp label and intended projector configuration.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.