01 Hero · CT4 projector case

2020–2021

Cadillac CT4 Projector Retrofit

Rear-Mounted Projector Carrier

INSTALLATION REFERENCE

Prepare the carrier with correctly oriented white clips, fasten the replacement projector behind the bracket and install the assembly in the original housing. For high-power LED projectors, the supplier recommends a standard H4 upgraded wiring harness.

◇ Cadillac CT4 ◇ Rear-Mounted Projector ◇ High-Power H4 Harness Recommendation

View Installation Guide

2020–2021 Cadillac CT4 front headlamp2020–2021 CT4 Reference
02 Vehicle application

CT4 Projector Bracket Application

Models
Cadillac CT4
Years
2020–2021
Headlamp
Pictured OEM hard-cure-sealant headlamp
Layout
Replacement projector mounted directly behind the carrier
Factory Parts
Restore the trim bezel and surrounding original lamp components
CT4 carrier pair white clips and hardware
Clip Direction

Match the white clips to the reference; do not reverse them.

Rear Mounting

Place the projector behind the bracket as illustrated.

High-Power Supply

Use the recommended standard H4 upgraded harness for high-power LED projectors.

03 Mounting preparation

Check Clip Direction and Projector Position

Prepare the White Clips

Step 01

Prepare the White Clips

Install the clips at the photographed positions and in the specified direction.

Mount Behind the Bracket

Step 02

Mount Behind the Bracket

Fasten the projector directly behind the carrier and verify hardware clearance.

04 Compatibility notice

Match the Pictured CT4 Lamp and Projector Body

Documented Configuration

  • 2020–2021 CT4 reference lamp
  • Replacement carrier with white clips
  • Projector mounted behind the bracket
  • H4 upgraded harness recommendation for high-power LEDs

Not Automatically Confirmed

  • Other lamp variants share the same carrier
  • Clips may be reversed
  • All projector bodies clear the housing unchanged
  • A decoder or original-source retention rule is established

Request Matching

Send lamp labels, carrier mounting photos and projector dimensions and power rating.

Request Verification

05 Installation process

Prepare and Fit the Rear-Mounted Projector Assembly

Open the Original Lamp

Step 01

Open the Original Lamp

The supplied photograph identifies hard-cure sealant. Protect retained lamp components during opening.

Remove the Bezel and OEM Projector

Step 02

Remove the Bezel and OEM Projector

Remove the surrounding trim and original optical assembly to expose the carrier points.

Install the Carrier Clips

Step 03

Install the Carrier Clips

Match the white clip positions and direction.

Secure the Replacement Projector

Step 04

Secure the Replacement Projector

Mount the projector directly behind the replacement bracket.

Install the Carrier in the Housing

Step 05

Install the Carrier in the Housing

Seat and secure the assembly, then inspect actual body clearance.

Restore and Check the Front Trim

Step 06

Restore and Check the Front Trim

Refit the surrounding bezel and check the projector aperture and front-cover clearance.

06 Electrical reference

H4 Upgraded Harness Recommended for High-Power LED Projectors

CT4 high positive low positive and negative connector reference
The photo labels high-beam positive, low-beam positive and negative. Follow the actual connector orientation; universal numbered pin assignments are not supplied.

High-Power Harness Recommendation

The supplier recommends a standard H4 upgraded wiring harness when fitting high-power LED projectors.

Confirm Other Requirements

The source does not establish a decoder or OEM-source retention requirement. Confirm the actual electrical arrangement and test both beams before closure.

07 Components to confirm

Match the CT4 Installation Parts

Replacement Carrier

Match the photographed CT4 mounting points.

White Mounting Clips

Do not install backwards.

Projector and Fasteners

Mount behind the carrier and check actual body clearance.

H4 Upgraded Harness

Recommended by the supplier for high-power LED projectors.

08 Installation result

Completed CT4 Projector Headlamp

Completed Cadillac CT4 projector retrofit

Verify low/high beams, retained lamp functions, beam aim and cover clearance before final sealing.

09 Installation photographs

CT4 Projector Details

10 Frequently asked questions

CT4 Projector Retrofit FAQ

Which lamp is documented?

The source covers the pictured 2020–2021 Cadillac CT4 headlamp. Match the actual label and internal mounting arrangement.

How are the clips installed?

Fit the white clips at the photographed positions without reversing their direction.

Where is the projector mounted?

The projector mounts directly behind the replacement bracket.

Which harness is recommended?

For high-power LED projectors, the supplier recommends a standard H4 upgraded wiring harness.

What circuit labels are provided?

The wiring photo identifies high-beam positive, low-beam positive and negative without universal numbered pin assignments.

Does the source confirm decoder or source-retention requirements?

No. Confirm those details for the actual lamp and selected projector rather than importing another model wiring rule.

Technical reference: Supplier article 246 and supplied photographs. Confirm clip orientation, rear mounting, connector functions and power-appropriate harness selection.

Related Headlight Retrofit Cases

Match Your CT4 Projector Bracket

Send lamp labels and projector dimensions and power rating for matching.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.