01 Hero · dual-option G60 case

2024

BMW 5 Series G60 Quad-Projector & Outer-Position Retrofit

Two Vehicle-Specific Projector Bracket Systems
INSTALLATION REFERENCE

One reference for two G60 solutions: a combined inner/outer bracket system for a complete quad-projector conversion, and a dedicated outer-position bracket for a simpler single-position upgrade.

◇ 2024 BMW 5 Series G60◇ Quad-Projector Kit◇ Outer-Position Kit◇ ZKW Cold-Sealed Headlamp

Compare Both Options

2024 BMW 5 Series G60 headlamp2024 BMW G60 Headlamp
02 Option guide

Choose the Complete Quad Kit or Outer-Position Upgrade

The two kits share the same headlamp reference and beam signals, but use different carriers, trim panels and installation scope.

Models
BMW 5 Series G60
Years
2024
Headlamp
Factory unit shown
Layout
Quad conversion / outer-position kit
Factory Parts
Original clips, fasteners and trim where specified
2024 BMW G60 combined inner outer quad-projector bracket kit
Match the Actual Lamp

Verify the lamp label and pictured internal mounting points before ordering.

Keep Layouts Separate

Follow the position or version-specific installation details below.

Verify Retained Parts

Use the documented original parts and wiring for the selected configuration.

2024 BMW G60 combined inner outer quad-projector bracket kit

Complete Quad-Projector System

  • Combined inner and outer vehicle-specific carriers
  • Supports complete four-projector conversion
  • Includes flip-over components and rear bracket hardware
  • Uses side and large inner decorative panels
  • Also documents a reduced single-position configuration

View Quad Steps

2024 BMW G60 outer-position projector bracket kit

Outer-Position Projector System

  • Dedicated driver/passenger outer carriers
  • Retains the factory retaining clip and fastener
  • Uses a dedicated side baffle
  • Restores the factory decorative shroud
  • Requires only local upper trimming when necessary

View Outer Steps

03 Technical comparison

Flip-Over Components, Beam Pins and Decorative Clearance

BMW G60 driver side quad bracket and flip-over components

Match the Factory Mounting Holes

Align the main carrier with the original projector points and install the flip-over components in their shown orientation.

BMW G60 low and high beam pin reference

Verify Four Beam Signals

Confirm pins 3, 4, 9 and 10 for low/high positive and negative before connection.

BMW G60 outer bracket side baffle installation

Restore the Side Baffle

The outer-only kit uses its dedicated side baffle to control the finished opening and trim appearance.

04 Compatibility notice

Confirm the Exact 2024 BMW G60 ZKW Headlamp

Quad Kit Applies To

  • 2024 BMW G60 headlamp matching the supplied reference
  • Combined inner/outer carrier mounting points
  • Compatible flip-over components and factory adjusters
  • Verified projector depth and decorative-panel clearance

Outer Kit Applies To

  • Same pictured G60 headlamp with outer-position upgrade
  • Matching factory retaining clip and projector fastener
  • Dedicated side baffle and restored factory shroud
  • Local upper trim only where the reference shows interference

Send Photos for Verification

Provide the year, lamp label, front lighting signature, projector carrier, flip-over parts, trim panels and connectors.

Request Option Verification

05A Quad-projector installation

Combined Inner / Outer Bracket Sequence

Open the ZKW Cold-Sealed Headlamp

Step 01

Open the ZKW Cold-Sealed Headlamp

Use controlled heat and professional tools to separate the front cover.

Remove the Decorative Trim

Step 02

Remove the Decorative Trim

Release the factory trim and retain all reusable panels and locating tabs.

Remove the Outer Projector

Step 03

Remove the Outer Projector

Remove the factory projector and keep the included fastener for the new carrier.

Prepare the Inner Decorative Panel

Step 04

Prepare the Inner Decorative Panel

Trim and install the inner panel around the projector position with verified clearance.

Install the Combined Bracket

Step 05

Install the Combined Bracket

Seat the bracket, pre-tighten one screw, then flip it into position and secure the lower fastener.

Install the Quad Projectors

Step 06

Install the Quad Projectors

Mount the selected projectors directly, restore the trim panels and verify upper/lower clearance.

05B Outer-position installation

Dedicated Outer-Position Bracket Sequence

Open the ZKW Cold-Sealed Headlamp

Step 01

Open the ZKW Cold-Sealed Headlamp

Separate the front cover with controlled heat and protect the factory trim.

Remove the Decorative Trim

Step 02

Remove the Decorative Trim

Remove the front decorative assembly and retain the locating hardware.

Remove the Factory Outer Projector

Step 03

Remove the Factory Outer Projector

Keep the specified factory fastener for installation on the new outer carrier.

Install the Factory Retaining Clip

Step 04

Install the Factory Retaining Clip

Transfer the original retaining clip to the marked bracket position.

Install the Outer Metal Bracket

Step 05

Install the Outer Metal Bracket

Mount the carrier at the factory points and confirm the flip-over accessory moves freely.

Preinstall the Projector and Shroud

Step 06

Preinstall the Projector and Shroud

Install the projector, snap the decorative shroud into place and trim the upper section only if required.

Combined Installation Gallery

06 Components to confirm

Match the Complete Hardware for the Selected Option

Combined Inner / Outer Quad Bracket Kit

Confirm both handed main carriers, rear components, flip-over accessories, fasteners and decorative panels.

Outer-Position Projector Bracket Kit

Match the dedicated left/right outer carriers, side baffles, factory retaining clips and supplied hardware.

Compatible Projectors and Shrouds

Verify projector body depth, mounting pattern, factory or A-type decorative shrouds and clearance.

Factory Trim and Beam Wiring

Retain the side/inner decorative panels and verify pins 3, 4, 9 and 10 before connecting the low/high-beam functions.

Completed 2024 BMW G60 quad-projector retrofit
07 Installation result

Selected Projector Layout behind the Restored Factory Trim

The completed reference retains the original G60 front appearance while supporting either the outer-position or full quad-projector layout.

  • Correct G60 headlamp and retrofit scope confirmed
  • Flip-over parts and factory fasteners retained
  • Selected brackets secured at original mounting points
  • Decorative panels trimmed only at marked interference areas
  • Low/high functions, clearance, aim and cold seal restored
08 Frequently asked questions

2024 BMW G60 Projector Bracket FAQ

What is the difference between the two BMW G60 bracket systems?

The quad-projector kit contains combined inner and outer carriers for a complete four-projector layout. The outer-position kit upgrades only the outer projector position and uses a simpler carrier and side baffle.

Which headlamp is covered?

Both references cover the pictured 2024 BMW 5 Series G60 factory ZKW cold-sealed headlamp. Confirm the lamp label, projector carrier and decorative-trim layout before ordering.

Can the quad kit be installed as a single-position conversion?

Yes. The supplied reference includes a single-position configuration using the applicable carrier and factory projector attachment, as well as the full quad-projector layout.

Which factory components are retained?

Retain the factory flip-over components, projector fastener, decorative shrouds, side and inner trim panels, adjusters and all reusable attachment hardware identified in the selected sequence.

What trim work is required?

Trim only the photographed areas of the factory outer decorative trim, inner decorative panel or local upper clearance. Check both upper and lower clearance before final assembly.

Which wiring pins are shown?

The source identifies pin 3 as low-beam positive, pin 4 as low-beam negative, pin 9 as high-beam negative and pin 10 as high-beam positive. Verify polarity on the vehicle before connection.

Technical reference: Based on Royalin-supplied installation photography and articles 892 and 893 for the pictured 2024 BMW G60 quad-projector and outer-position bracket systems. Verify the lamp label, selected option, projector dimensions, trim clearance and wiring before ordering.

Related Headlight Retrofit Cases

09 Business inquiry

Need the Correct 2024 BMW G60 Bracket?

Send the lamp label, internal carrier, flip-over components and desired outer-only or quad-projector configuration.

Professional cold-seal opening, trim preparation, wiring verification, resealing and beam aiming are recommended.

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.