01 Hero · S5 / RS5 dual-position case

2020–2024

Audi S5 / RS5 B9.5 Projector Retrofit

Outer Square Projector and Compact Inner Projector Brackets

INSTALLATION REFERENCE

Two distinct mounting systems for the pictured facelift lamp: an outer 3-inch square projector and 1.5–1.7-inch short-tail projectors at the inner position.

◇ S5 / RS5 B9.5 ◇ Original Sources Retained ◇ Separate-Negative Harness

View Installation Guide

2020–2024 Audi S5 RS5 vehicle front and headlamp2020–2024 S5 / RS5 Reference Lamp
02 Vehicle application

S5 and RS5 Shared Bracket Application

Models
Audi S5 / RS5 B9.5 Facelift
Years
2020–2024
Headlamp
Pictured OEM Marelli hard-cure-sealant lamp
Layout
Outer 3-inch square projector + inner 1.5–1.7-inch short-tail projectors
Factory Parts
Original light sources retained; original optical assemblies removed from converted positions
Outer 3-inch bracket pair
Two Models, One Reference

Match actual lamp internals for both S5 and RS5.

Outer Square Optics

3-inch square optics only.

Inner Compact Optics

1.5–1.7-inch short-tail optics only.

03 Position-specific systems

Show Both Outer and Inner Brackets

Outer Projector Bracket

Step 01

Outer Projector Bracket

The supplier specifies a 3-inch square projector only. Outer-only conversion is permitted.

Inner Compact-Projector Bracket

Step 02

Inner Compact-Projector Bracket

The inner carrier is for 1.5–1.7-inch short-tail projectors. Do not substitute a full-length projector body. Inner-only conversion is permitted.

04 Compatibility notice

Confirm the Optics and Electrical Arrangement

Documented Configuration

  • 2020–2024 S5 / RS5 B9.5 reference lamp
  • Outer 3-inch square optics
  • Inner 1.5–1.7-inch short-tail projectors
  • Retained sources and separate-negative wide-voltage harness

Not Automatically Confirmed

  • Different lamp internals or specifications
  • Round outer projector clearance
  • Full-length projectors at the inner position
  • Common-negative wiring

Request Matching

Send the lamp label and both optical mounting positions for verification.

Request Verification

05 Shared preparation

Open the Lamp and Remove the Trim in Order

Open the Marelli Lamp

Step 01

Open the Marelli Lamp

The pictured OEM Marelli lamp has hard-cure sealant. Open the front cover for the documented conversion.

Remove the X-Shaped Stainless Trim

Step 02

Remove the X-Shaped Stainless Trim

Carefully release the original X-shaped stainless-steel trim before removing the frame sections.

Remove the Upper Trim Frame

Step 03

Remove the Upper Trim Frame

Remove the upper frame, followed by the lower trim frame shown in the next photograph.

05A Outer-position conversion

Outer Square Projector and Retaining-Ring Orientation

Orient the Lower Plastic Ring

Step 01

Orient the Lower Plastic Ring

The bent protrusion faces forward and the ring opening faces inward. Do not reverse the illustrated orientation.

Remove the Original Optical Modules

Step 02

Remove the Original Optical Modules

Carefully remove the original inner and outer optical modules as illustrated while retaining the original sources required by the electrical arrangement.

Check Outer Mounting and Projector Choice

Step 03

Check Outer Mounting and Projector Choice

The photo illustrates front mounting with one spacer post and one nut. Although this supplied image shows a round projector, the supplier text specifies a 3-inch square projector only; follow that stated limitation.

05B Inner-position conversion

Prepare the Compact Inner Carrier and Trim Plate

Detach the Accessory Piece

Step 01

Detach the Accessory Piece

Identify the removable accessory and trim plate. Match the carrier arrangement to the selected short-tail projector.

Assemble the Inner Carrier

Step 02

Assemble the Inner Carrier

Install the upright carrier and the illustrated trim plate in the photographed orientation.

Install the Inner Projectors

Step 03

Install the Inner Projectors

Use only 1.5–1.7-inch short-tail projectors at the inner high-beam position. Check the actual body length and surrounding clearance.

05C Restoration

Restore the Lower and Upper Trim

Identify the Lower Trim Fixings

Step 01

Identify the Lower Trim Fixings

Keep track of the lower trim frame removed during preparation so its fixings can be restored correctly.

Refit the Trim Frame

Step 02

Refit the Trim Frame

Check the refitting detail against both projector positions and ensure the original frame clears the new optics.

Inspect the Completed Headlamp

Step 03

Inspect the Completed Headlamp

Check mounting security, beam functions, alignment and internal clearance before final closure.

06 Electrical requirements

Retain the Original Sources and Use Separate Negatives

The supplier requires original light-source retention and a wide-voltage harness with independent negative circuits. Do not use a common-negative harness.

No connector polarity or numbered pinout is provided in the supplied installation reference. Verify the actual circuits before connection; do not transfer wiring definitions from another model.

07 Components to confirm

Match Both Position-Specific Kits

Outer Bracket Pair

Match the square-projector carrier and lower retaining-ring orientation.

Inner Matrix Carrier

Match the upright carrier, trim plate and short-tail optics.

Projectors and Trim

Outer 3-inch square only; inner 1.5–1.7-inch short-tail only.

Separate-Negative Harness

Retain original sources and match wide-voltage wiring.

08 Installation result

Independent Outer or Inner Conversion

Completed S5 RS5 facelift headlamp

The supplier permits outer-only or inner-only conversion, as well as a combined installation. Match each position to its own projector size restriction.

09 Installation photographs

Detailed S5 / RS5 Installation References

10 Frequently asked questions

Audi S5 / RS5 Retrofit FAQ

Which models are documented?

The supplier covers 2020–2024 Audi S5 and RS5 B9.5 facelift reference lamps. Match the actual lamp label and internals.

Which projector fits the outer position?

The supplier text specifies a 3-inch square projector only. Do not use the round projector visible in the supplied installation photograph as confirmation of round-projector compatibility.

Which projector fits the inner position?

Only 1.5–1.7-inch short-tail projectors are specified for the inner high-beam position. Check actual body dimensions.

Can one position be converted alone?

Yes. The supplier explicitly permits either outer-only or inner-only conversion.

How is the lower retaining ring oriented?

The bent protrusion faces forward and the opening faces inward. Do not reverse the photographed orientation.

What electrical setup is required?

Retain original sources and use a wide-voltage harness with independent negative circuits. No connector polarity or universal pinout is supplied.

Technical reference: Supplier article 1535 and supplied installation photographs. Confirm lamp specification, retaining-ring orientation, short-tail inner optics and separate-negative harness.

Related Headlight Retrofit Cases

Match Your S5 / RS5 Brackets

Send the lamp label, inner and outer mounting positions and connector photographs for matching.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.