01 Hero · S3 / RS3 dual-position case

2016

Audi S3 / RS3 8V Projector Retrofit

Outer Square Projector and Twin Inner Matrix Brackets

INSTALLATION REFERENCE

Two distinct mounting systems for the pictured pre-facelift lamp: an outer 3-inch square projector and two high-beam-only matrix modules at the inner position.

◇ S3 / RS3 8V ◇ Original Sources Retained ◇ Separate-Negative Harness

View Installation Guide

2016 Audi S3 RS3 vehicle front and headlamp2016 S3 / RS3 Reference Lamp
02 Vehicle application

S3 and RS3 Shared Bracket Application

Models
Audi S3 / RS3 8V Pre-Facelift
Years
2016
Headlamp
Pictured OEM Hella hard-cure-sealant lamp
Layout
Outer 3-inch square projector + two inner high-beam-only matrix modules
Factory Parts
Original light sources retained; original optical assemblies removed from converted positions
Outer 3-inch bracket pair
Two Models, One Reference

Match actual lamp internals for both S3 and RS3.

Outer Square Optics

Compound-eye type preferred, with low beam above.

Inner High-Beam Only

Two single-high-beam matrix modules only.

03 Position-specific systems

Show Both Outer and Inner Brackets

Outer Projector Bracket

Step 01

Outer Projector Bracket

The source recommends a 3-inch square projector, preferably compound-eye with low beam above. The installation photo specifies square-only fitment.

Inner Twin-Matrix Bracket

Step 02

Inner Twin-Matrix Bracket

The inner carrier is for two high-beam-only matrix projectors. Do not substitute bi-beam matrix modules.

04 Compatibility notice

Confirm the Optics and Electrical Arrangement

Documented Configuration

  • 2016 S3 / RS3 8V reference lamp
  • Outer 3-inch square optics
  • Two inner high-beam-only matrix modules
  • Retained sources and separate-negative wide-voltage harness

Not Automatically Confirmed

  • Different lamp internals or specifications
  • Round outer projector clearance
  • Bi-beam matrix modules at the inner position
  • Common-negative wiring

Request Matching

Send the lamp label and both optical mounting positions for verification.

Request Verification

05 Shared preparation

Open the Lamp and Remove the Original Optics

Remove the Front Lens Cover

Step 01

Remove the Front Lens Cover

The pictured lamp is OEM Hella with hard-cure sealant. Open the front lens cover for the documented conversion.

Remove the Trim Frame

Step 02

Remove the Trim Frame

Carefully release and remove the original frame to expose both optical positions.

Remove the Inner Reflector

Step 03

Remove the Inner Reflector

Remove the original inner high-beam reflector. The following photograph also shows removal of the outer light module.

05A Outer installation

Outer Square Projector and Vertical Adjustment

Remove the Outer Light Module

Step 01

Remove the Outer Light Module

Remove the illustrated outer optical module while preserving the original sources required for the electrical arrangement.

Fit the Outer Bracket and Projector

Step 02

Fit the Outer Bracket and Projector

Use a 3-inch square projector. The slotted mounting holes allow vertical adjustment for the chosen projector.

Check the Optional Shroud

Step 03

Check the Optional Shroud

The pictured shroud is optional and sold separately. Verify its clearance and alignment before restoring the frame.

05B Inner carrier assembly

Observe the Angled Small-Component Installation

Separate the Marked Pieces

Step 01

Separate the Marked Pieces

Identify the passenger-side inner carrier components and detach the indicated small pieces.

Keep the Required Angle

Step 02

Keep the Required Angle

The small component is installed at an angle as illustrated. Do not straighten its mounting orientation.

Complete the Inner Carrier

Step 03

Complete the Inner Carrier

Use the small-component detail and assembled-carrier photographs to match the fixing orientation before adding the optics.

05C Inner matrix installation

Fit Two High-Beam-Only Matrix Modules

Install the Matrix Modules

Step 01

Install the Matrix Modules

Use two single-high-beam matrix projectors only, mounted to the prepared inner carrier.

Install the Inner Carrier in the Housing

Step 02

Install the Inner Carrier in the Housing

Place the complete matrix assembly into the rear housing and secure it at the documented mounting points.

Refit the Trim Frame

Step 03

Refit the Trim Frame

Restore the original trim frame after checking both projector positions and local clearance.

06 Electrical requirements

Retain the Original Sources and Use Separate Negatives

The supplier requires original light-source retention and a wide-voltage harness with independent negative circuits. Do not use a common-negative harness.

No connector polarity or numbered pinout is provided in the supplied installation reference. Verify the actual circuits before connection; do not transfer wiring definitions from another model.

07 Components to confirm

Match Both Position-Specific Kits

Outer Bracket Pair

Match the square-projector carrier and slotted height adjustment.

Inner Matrix Carrier

Match the angled component and twin high-beam-only modules.

Projectors and Trim

Outer compound-eye square optics preferred; optional shroud sold separately.

Separate-Negative Harness

Retain original sources and match wide-voltage wiring.

08 Installation result

Inspect Both Positions Before Final Closure

S3 RS3 completed front installation detailS3 RS3 completed headlamp assembly

Check mounting security, trim clearance, beam functions and alignment before final closure.

09 Installation photographs

Detailed S3 / RS3 Installation References

10 Frequently asked questions

Audi S3 / RS3 Retrofit FAQ

Which models are covered?

The reference covers the pictured 2016 Audi S3 and RS3 8V pre-facelift lamp. Verify the actual lamp internals for each model.

What fits the outer position?

Use a 3-inch square projector. A compound-eye type with low beam above is preferred by the supplier; the installation image specifies square-only fitment.

What fits the inner position?

Only two high-beam-only matrix projectors are specified. This is not an inner bi-beam matrix application.

What is important when assembling the inner carrier?

Detach the marked small pieces and install the indicated component at the illustrated angle. Match the carrier assembly photographs before installation.

Is the shroud included?

The installation photograph identifies the shroud as optional and sold separately. Verify clearance before use.

What electrical setup is required?

Retain the original sources and use a wide-voltage harness with separate negative circuits. No universal connector pinout is supplied.

Technical reference: Supplier article 1495 and supplied installation photographs. Confirm lamp specification, angled inner carrier, high-beam-only matrix modules and separate-negative harness.

Related Headlight Retrofit Cases

Match Your S3 / RS3 Brackets

Send the lamp label, inner and outer mounting positions and connector photographs for matching.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.