01 Hero · Q7 high-spec dual-position case

2016–2019

Audi Q7 4M High-Spec Projector and Matrix Retrofit

Outer 3-Inch Square Projector · Inner Triple Matrix

INSTALLATION REFERENCE

Separate bracket options for the pictured high-spec lamp: one outer 3-inch square projector and an inner three-module matrix carrier. Convert either position independently or combine both.

◇ Q7 4M Pre-Facelift ◇ High Specification ◇ Original Sources Retained

View Installation Guide

2016–2019 Audi Q7 4M high-spec vehicle headlampQ7 High-Spec Reference Headlamp
02 Vehicle application

Q7 High-Spec Dual-Position Application

The supplier specifies original-source retention and an independent-negative wide-voltage harness. Outer and inner carriers can be installed separately; match the actual lamp internals and mounting positions.

Models
Audi Q7 4M Pre-Facelift
Years
2016–2019
Headlamp
High-spec reference; pictured OEM ZKW hard-cure-sealant lamp
Layout
Outer 3-inch square projector; inner triple 1.5–1.8-inch matrix
Factory Parts
Original sources retained; trim and self-test clearance checked
Driver-side outer projector and inner triple-matrix bracket components
Independent Position Options

Convert outer low beam, inner high beam or both.

Different Projector Sizes

Outer: 3-inch square only. Inner: 1.5–1.8-inch modules, maximum 56 mm width.

Retained-Source Wiring

Keep original sources; use separate negative circuits with a wide-voltage harness.

03 Position-specific carriers

Show Both Bracket Sets

Outer Low-Beam Carrier

Position 01

Outer Low-Beam Carrier

Pair the dedicated carrier with a 3-inch square projector. Prepare mounting posts and clips; the projector sits behind the carrier.

Inner Triple-Matrix Carrier

Position 02

Inner Triple-Matrix Carrier

Use three 1.5–1.8-inch modules in the pictured inner arrangement. The installation photo specifies maximum projector width of 56 mm.

04 Compatibility notice

Match the High-Spec Lamp and Required Clearances

Documented Configuration

  • 2016–2019 Q7 high-spec reference lamp
  • Outer 3-inch square projector only
  • Inner 1.5–1.8-inch modules; maximum 56 mm width
  • Original sources and separate-negative wide-voltage harness

Not Automatically Confirmed

  • 2016 D5S 25W rear-access bracket procedure
  • Round outer projectors or wider inner modules
  • Common-negative harness substitution
  • Clearance based only on static fit without self-test

Request Matching

Send the lamp label, source connectors and both mounting positions.

Request Verification

05 Shared preparation

Open and Prepare the High-Spec Lamp

Identify the Original Lamp

Step 01

Identify the Original Lamp

The reference photo identifies a ZKW headlamp with hard-cure sealant. Match this high-spec configuration before work.

Remove the Front Lens Cover

Step 02

Remove the Front Lens Cover

Open the headlamp cover for the illustrated internal conversion. This is distinct from the 25W xenon rear-access case.

Remove the Trim Frame

Step 03

Remove the Trim Frame

Remove the front trim frame carefully to expose the outer projector and inner high-beam mounting areas.

05A Outer low-beam installation

Prepare the Posts and Rear-Mount the 3-Inch Projector

Prepare the Carrier Hardware and Clips

Outer Step 01

Prepare the Carrier Hardware and Clips

Fit the pictured outer carrier clips and mounting hardware in their illustrated locations.

Secure the Mounting Posts First

Outer Step 02

Secure the Mounting Posts First

Fasten the posts first. The photo places the projector behind the bracket, approximately one post length rearward; verify the actual hardware.

Fasten the Projector and Outer Trim Plate

Outer Step 03

Fasten the Projector and Outer Trim Plate

Secure the projector behind the bracket and fasten the outer trim plate together with it as pictured.

05B Inner high-beam installation

Assemble and Install the Triple-Matrix Carrier

Assemble the Inner Bracket

Inner Step 01

Assemble the Inner Bracket

Match the inner triple carrier and supporting bracket to the side-specific hardware layout.

Fit Three Compatible Matrix Modules

Inner Step 02

Fit Three Compatible Matrix Modules

Use 1.5–1.8-inch projectors, maximum 56 mm wide. Check each body against the pictured carrier and available clearance.

Mount the Inner Carrier in the Rear Housing

Inner Step 03

Mount the Inner Carrier in the Rear Housing

Mount the matrix carrier directly into the rear housing. If a projector rear body touches the plastic behind it, relieve only the small marked interference area.

05C Self-test clearance

Check Movement before Closing the Lamp

Check the Outer Side Trim during Self-Test

Check 01

Check the Outer Side Trim during Self-Test

Operate the lamp self-test and inspect the outer low-beam side trim plate for contact throughout its movement.

Check Front Trim and Relieve Locally if Needed

Check 02

Check Front Trim and Relieve Locally if Needed

Check the front trim plate during the self-test. Trim only the interfering local area where necessary; repeat the movement check before closure.

06 Electrical reference

Retain Sources and Keep Negative Circuits Separate

Retain the original light sources and use an independent-negative wide-voltage harness. Do not replace this requirement with a common-negative arrangement.

Pictured low-beam source connector with positive and negative terminals marked
Low-beam polarity reference at the pictured source connector.
Pictured high-beam source connector with positive and negative terminals marked
High-beam polarity reference at its separate source connector.

Match each connector to its photo orientation and verify actual polarity. The source does not provide a universal pin-number table for other lamp variants.

07 Components to confirm

Match Both Carrier Systems

Outer Carrier and Trim Plate

Match mounting posts, blue clips and the rear-mounted projector position.

Inner Triple Carrier

Match side, support hardware and three module mounting points.

Position-Specific Projectors

Outer 3-inch square only; inner 1.5–1.8-inch modules up to 56 mm wide.

Retained-Source Harness

Use independent negative circuits and wide-voltage wiring; retain original sources.

08 Installation result

Front Detail and Customer Result

Q7 high-spec outer projector and inner triple-matrix front detail
Completed front trim arrangement.
Q7 high-spec customer installation result
Supplier customer-result photograph; verify functions, aim, self-test movement and sealing on the actual lamp.
09 Installation photographs

Detailed High-Spec Installation References

10 Frequently asked questions

Q7 High-Spec Projector and Matrix Retrofit FAQ

Which configuration is documented?

The supplier documents the 2016–2019 Q7 high-spec headlamp, with outer 3-inch square projector and inner triple-matrix bracket options. Match the actual lamp internals.

Can the outer or inner position be converted independently?

Yes. Either the outer low-beam or inner high-beam position can be converted on its own, or both can be combined.

Which projectors fit each position?

The outer position accepts only 3-inch square projectors. The inner carrier fits 1.5–1.8-inch modules; the installation photo specifies a maximum projector width of 56 mm.

Must the original light sources remain?

Yes. Retain the original sources and use a wide-voltage harness with separate negative circuits. A common-negative harness is not the specified arrangement.

How is the outer projector positioned?

Secure the posts first, then mount the projector behind the carrier, approximately one post length rearward as pictured. Fasten the outer trim plate with the projector.

Which interference checks are shown?

Check rear plastic clearance at the inner modules and both outer side/front trim clearances during the lamp self-test. Relieve only the marked local interference areas and repeat the movement check before closure.

Technical reference: Supplier article 913 and supplied photographs. Verify lamp identity, each carrier and module size, retained-source wiring and moving clearance.

Related Headlight Retrofit Cases

Match Your Q7 High-Spec Brackets

Send the lamp label and both outer and inner mounting photographs.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.