01 Hero · Q5L dual-position case

2026

Audi Q5L Projector Retrofit

Outer Low-Beam and Inner High-Beam Bracket Options

INSTALLATION REFERENCE

A reference for the pictured 2026 Q5L headlamp, covering separate mounting positions, original clip transfer, local clearance work and retained-source wiring.

◇ 2026 Q5L ◇ 3-Inch Square Projectors ◇ Original Sources Retained

View Installation Guide

Completed 2026 Audi Q5L headlamp with outer and inner projectors2026 Q5L Completed Headlamp
02 Vehicle application

2026 Q5L Bracket Application

Use the carrier for the chosen lamp position. The supplier permits an outer-only, inner-only or combined conversion, with 3-inch square projectors only.

Models
Audi Q5L; pictured headlamp configuration
Years
2026
Headlamp
Pictured OEM Marelli hard-cure-sealant lamp
Layout
Separate outer low-beam and inner high-beam carriers
Factory Parts
Original light sources retained; pictured plastic retaining clip transferred
Passenger-side outer and inner Q5L brackets compared
Two Position Options

Fit the outer or inner position independently, or convert both.

3-Inch Square Only

Do not infer compatibility with other projector shapes.

Retain Original Sources

Use a wide-voltage harness with separate negative circuits.

03 Position-specific hardware

Show Both Outer and Inner Carrier Sets

Outer Low-Beam Brackets

Position 01

Outer Low-Beam Brackets

Select the matching side and transfer the OEM plastic retaining clip in its pictured orientation.

Inner High-Beam Brackets

Position 02

Inner High-Beam Brackets

Select the dedicated inner carrier. Check upper housing clearance and the compound-eye-projector clip clearance if applicable.

04 Compatibility notice

Confirm the Actual Lamp and Electrical Arrangement

Documented Configuration

  • 2026 Audi Q5L reference headlamp
  • 3-inch square projectors only
  • Outer and inner positions can be converted independently
  • Original sources retained with independent-negative wide-voltage harness

Not Automatically Confirmed

  • Other model years or different lamp internals
  • Round or differently sized projector bodies
  • Common-negative harness substitution
  • Removal of original sources or excessive housing trimming

Request Matching

Send the lamp label, carrier points and source connectors before ordering.

Request Verification

05 Shared preparation

Open and Prepare the Marelli Lamp

Remove the Headlamp Lens Cover

Step 01

Remove the Headlamp Lens Cover

The reference identifies a Marelli lamp with hard-cure sealant. Open the front cover for access to the internal components.

Remove the Daytime Running Light

Step 02

Remove the Daytime Running Light

Remove the daytime-running-light assembly carefully and protect it during subsequent work.

Remove Decorative Panel and Original Optics

Step 03

Remove Decorative Panel and Original Optics

Remove the decorative panel and original optics as shown. Keep the original light sources for the required retained-source electrical setup.

05A Outer low-beam installation

Transfer the OEM Clip and Front-Mount the Outer Projector

Transfer the OEM Plastic Retaining Clip

Outer Step 01

Transfer the OEM Plastic Retaining Clip

Fit the pictured original plastic retaining clip onto the replacement bracket in the illustrated orientation.

Install the Outer Carrier

Outer Step 02

Install the Outer Carrier

Install the outer low-beam bracket at the pictured housing attachment points and verify all clips are seated.

Front-Mount the Outer Projector

Outer Step 03

Front-Mount the Outer Projector

Fit the 3-inch square projector from the front and secure it directly as shown. Check seating and decorative-panel clearance.

05B Inner high-beam installation

Local Housing Clearance and Inner Carrier Fitment

Relieve the Upper Housing Locally

Inner Step 01

Relieve the Upper Housing Locally

Trim only the marked area above the high-beam position to clear the carrier. Do not remove too much material.

Install the Inner High-Beam Carrier

Inner Step 02

Install the Inner High-Beam Carrier

Compare the after-trimming reference and install the dedicated inner bracket using the pictured mounting points.

Check Compound-Eye Projector Clip Clearance

Inner Step 03

Check Compound-Eye Projector Clip Clearance

If using a compound-eye projector, relieve the specifically marked interference area at the clip. Do not generalize this cut to every projector body.

05C Restore the lamp trim

Decorative Panel and DRL Clearance

Relieve the High-Beam Decorative Panel

Trim Step 01

Relieve the High-Beam Decorative Panel

Trim the high-beam decorative panel only at the marked local interference points.

Reinstall Inner and Outer Panels

Trim Step 02

Reinstall Inner and Outer Panels

Restore both decorative panels and verify clearance around the installed projectors.

Relieve the DRL Support Locally

Trim Step 03

Relieve the DRL Support Locally

Trim the illustrated upper daytime-running-light support area at the high-beam position. The supplier photo states that exterior appearance is unaffected; verify the actual fit before closure.

06 Electrical reference

Retain the Sources and Keep Negative Circuits Separate

Retain the original light sources and use a wide-voltage harness with independent negative circuits. Do not substitute a common-negative harness.

Pictured Q5L low-beam source connector positive and negative reference
Low-beam polarity: use the orientation and marked terminals in this photograph.
Pictured Q5L high-beam source connector positive and negative reference
High-beam polarity: follow the separately pictured connector orientation.

These are photo-specific polarity references, not a universal pin-number table. Verify actual connections and preserve the required original sources.

07 Components to confirm

Match Both Mounting Positions

Outer Carrier Pair

Match side and OEM plastic retaining-clip orientation.

Inner Carrier Pair

Check local upper housing and optional compound-eye clip clearance.

3-Inch Square Projectors

The only projector size and shape specified by article 1634.

Retained-Source Harness

Wide-voltage wiring with independent negative circuits; retain original sources.

08 Result and final restoration

Restore the DRL and Verify the Complete Lamp

Reinstall the Daytime Running Light

Result 01

Reinstall the Daytime Running Light

Install the DRL into the rear housing after checking the local support clearance.

Completed Assembly Reference

Result 02

Completed Assembly Reference

Check fit, beam functions and retained-source connections before final lamp closure and sealing.

09 Installation photographs

Detailed Carrier and Clearance References

10 Frequently asked questions

2026 Q5L Retrofit FAQ

Which model year is covered?

This case describes the 2026 Q5L documented in supplier article 1634 and its installation photographs. Match the actual lamp configuration before ordering.

Can the outer or inner position be converted separately?

Yes. The supplier permits separate conversion of the outer low-beam or inner high-beam position, or a conversion of both positions.

Which projectors are specified?

Only 3-inch square projectors are specified. Compatibility with other projector dimensions or shapes is not confirmed.

Must the original light sources remain?

Yes. The supplier requires original-source retention and a wide-voltage harness with separate negative circuits.

What trimming is required at the inner position?

Relieve the marked upper housing and decorative-panel/DRL support areas locally. Compound-eye projector use also requires checking the marked retaining-clip interference. Do not remove excessive material.

What is transferred at the outer position?

Transfer the pictured OEM plastic retaining clip onto the carrier, install the outer bracket and front-mount the projector as illustrated.

Technical reference: Supplier article 1634 and supplied photographs. Verify lamp identity, bracket position, original-source retention, separate negative circuits and local clearance before installation.

Related Headlight Retrofit Cases

Match Your 2026 Q5L Brackets

Send the actual lamp label and inner/outer mounting photographs.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.