01 Hero · Q5 facelift non-adaptive case

2015–2018

Audi Q5 8R Facelift Non-Adaptive Projector Retrofit

Rear-Access Carrier · Front Lens Retained
INSTALLATION REFERENCE

A China-market non-adaptive lamp reference covering three support-point releases, original plastic-carrier removal and position-specific large/small retaining clips.

◇ Q5 8R Facelift◇ Non-Adaptive Reference◇ 10 mm / 8 mm Clips

View Installation Guide

China-market Audi Q5 non-adaptive headlamp2015–2018 Q5 Non-Adaptive
02 Vehicle application

Q5 Facelift Non-Adaptive Bracket Application

Match the China-market non-adaptive lamp and original carrier shown. This is separate from the imported Valeo reference and requires local internal support preparation despite keeping the front lens closed.

Models
Audi Q5 8R Facelift; China-market reference
Years
2015–2018
Headlamp
Non-adaptive reference configuration
Layout
Rear-access replacement metal carrier
Factory Parts
Front lens retained; original carrier removed; shroud may be reused
Q5 facelift non-adaptive bracket pair and clips
Clip Size Matters

One 10 mm large and two 8 mm small clips in the pictured arrangement.

Internal Preparation

Release three support points and cut only marked carrier sections.

Original Shroud Option

The supplier permits bonding the original shroud back in place.

03 Clip and support details

Check Sizes, Orientation and Release Points

10 mm large and 8 mm small retaining clip positions

Large and Small Clips

Use the pictured 10 mm/8 mm positions and orientation.

Optional drill access for original support release

Optional Drill Access

Use the source-marked point only if needed; no diameter is supplied.

Blue-marked plastic carrier cut locations

Local Carrier Cuts

Release the remaining round clip and cut only the indicated areas.

04 Compatibility notice

Confirm the Actual Non-Adaptive Lamp

Documented Configuration

  • 2015–2018 Q5 China-market non-adaptive reference
  • Front lens retained during rear access
  • 10 mm and 8 mm retaining-clip arrangement
  • Optional original-shroud reuse

Not Automatically Confirmed

  • Adaptive or imported Valeo mounting systems
  • Interchangeable clip sizes or reversed orientation
  • A conversion without internal carrier preparation
  • Copied wiring pins, decoding or driver-board instructions

Request Matching

Send the lamp label, original carrier and selected projector photos.

Request Verification

05 Installation process

Q5 Facelift Rear-Access Installation

Release the Three Original Support Points

Step 01

Release the Three Original Support Points

Work through rear access with the front lens retained. Release the three marked support points, using the optional illustrated drill access only if required.

Remove the Original Projector

Step 02

Remove the Original Projector

After all three points are released, pry the projector in the arrow direction and remove it through the rear opening.

Release the Original Carrier Clips

Step 03

Release the Original Carrier Clips

Use the illustrated modified screwdriver tip in the barb gap to release the locking barb, then release the other round clip in the same way.

Remove the Marked Plastic Carrier Sections

Step 04

Remove the Marked Plastic Carrier Sections

Cut only the blue-marked areas with cutters. Remove the original plastic carrier and decorative shroud as illustrated.

Install the Correct Clip Sizes and Metal Bracket

Step 05

Install the Correct Clip Sizes and Metal Bracket

Match the 10 mm large clip and two 8 mm small clips to the supplied orientation diagram, then fit the replacement metal carrier.

Secure the Replacement Projector and Shroud

Step 06

Secure the Replacement Projector and Shroud

Fit and secure the projector. Choose the optional small black shroud or securely bond the original shroud as the source permits, then verify adjustment and clearance.

Selected Installation Details

06 Components to confirm

Carrier, Sized Clips, Projector and Shroud

Non-Adaptive Carrier Pair

Match the China-market reference lamp and mounting system.

10 mm and 8 mm Clips

Follow the large/small clip locations and orientation.

Replacement Projector

Confirm fixing points and rear/front clearance.

Shroud Choice

Optional small black shroud or securely bonded original shroud.

07 Front fit and result

Verify Shroud Retention and Projector Clearance

Q5 replacement projector front close-up
Replacement projector front detail
Completed Q5 facelift non-adaptive retrofit
Completed reference headlamp
08 Frequently asked questions

Q5 Facelift Non-Adaptive Retrofit FAQ

Which lamp is documented?

The source covers the 2015–2018 Audi Q5 non-adaptive application. The photograph identifies a China-market non-adaptive headlamp. Match the actual lamp and original carrier; the imported Valeo case is a different reference.

How do the supplied clip sizes differ?

The kit photo specifies one 10 mm large clip and two 8 mm small clips per illustrated bracket. Match both size and orientation to the reference rather than treating all three clips as interchangeable.

Does the front lens need opening?

The procedure retains the front lens and works from the rear. The original support points and plastic carrier are still released/cut at the marked locations.

How is the original projector released?

Release the three marked support points, drilling the illustrated point only if needed, then pry in the marked direction and remove the projector. Use the modified tool to release the clip barbs and cut the blue-marked carrier areas.

Can the original decorative shroud be reused?

Yes. Article 131 says the original shroud can be bonded back in place. A small black replacement shroud is also recommended as an optional appearance choice; verify fit and secure retention.

Does this source specify wiring or decoding?

No. Article 131 does not provide a universal pinout, decoding requirement or driver-board input instruction. Confirm the selected projector electrical setup separately instead of copying the imported Valeo procedure.

Technical reference: Supplier article 131 and supplied photographs. Verify lamp identity, clip sizes/orientation, support release, local carrier cuts and shroud retention.

Related Headlight Retrofit Cases

Match Your Q5 Facelift Non-Adaptive Bracket

Send the original lamp and mounting photographs.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.