01 Hero · Q4 e-tron matrix case

2023–2024

Audi Q4 e-tron 89A Mid/Base-Spec Matrix Retrofit

Four 1.5–1.8-Inch Matrix Projectors per Lamp
INSTALLATION REFERENCE

A retained-source reference with handed main carriers, four projector positions and a wide-voltage harness that may use either common or independent negatives.

◇ Q4 e-tron 89A◇ Four Projectors per Lamp◇ Original Sources Retained

View Installation Guide

Audi Q4 e-tron vehicle front and headlamp2023–2024 Q4 e-tron Reference
02 Vehicle application

Q4 e-tron Matrix Kit Application

The supplier supports four 1.5–1.8-inch projectors per lamp and requires original-source retention. Common-negative and independent-negative wide-voltage harnesses are both permitted for this documented model.

Models
Audi Q4 e-tron 89A
Years
2023–2024
Headlamp
Mid/base-spec reference; hard-cure sealant
Layout
Four 1.5–1.8-inch matrix projectors per lamp
Factory Parts
Original light sources retained; DRL restored
Complete Q4 matrix kit and projector sub-brackets
Four Matrix Positions

Match the 1.5–1.8-inch hole pattern and actual projector fit.

Original Sources Retained

Verify the pictured source-board polarity.

Two Harness Options

Common-negative or independent-negative wide-voltage harness.

03 Source and wiring reference

Verify Polarity on the Retained Sources

Identical low and high beam light source types

Matching Source-Board Types

The source identifies identical low- and high-beam boards and matching pickup locations.

Source-board positive and negative pickup locations

Actual Connector Polarity

Follow the pictured positive/negative locations. With a common-negative H4 harness, take negative from the main connector negative as specified; no universal pin number is supplied.

04 Compatibility notice

Confirm the Mid/Base-Spec Lamp

Documented Configuration

  • 2023–2024 Q4 mid/base-spec reference
  • Four 1.5–1.8-inch matrix projectors per lamp
  • Original light sources retained
  • Common-negative or independent-negative wide-voltage harness

Not Automatically Confirmed

  • Other lamp trims without matching
  • Source removal or copied decoding assumptions
  • Unverified connector polarity or guessed pins
  • DRL reassembly without checking upper projector clearance

Request Matching

Send the lamp label, source-board connectors and projector dimensions.

Request Verification

05 Installation process

Q4 Matrix Carrier Installation

Open the Front Lens Cover

Step 01

Open the Front Lens Cover

The source identifies hard-cure sealant. Open the front lens cover and protect the DRL and surrounding trim.

Remove the Original Reflector Assembly

Step 02

Remove the Original Reflector Assembly

Remove the original reflector assembly to expose the mounting layout. Retain the original light sources for the required electrical setup.

Fit the Supplied Retaining Clips

Step 03

Fit the Supplied Retaining Clips

Match the clip orientation and carrier fixing arrangement to the supplied installation detail.

Select and Assemble the Handed Carrier

Step 04

Select and Assemble the Handed Carrier

Use the correct side-specific main carrier and attach the projector sub-brackets as illustrated.

Install Four Matrix Projectors

Step 05

Install Four Matrix Projectors

Fit four compatible 1.5–1.8-inch matrix projectors per lamp. Check actual mounting dimensions and individual clearances.

Mount the Complete Carrier and Restore the DRL

Step 06

Mount the Complete Carrier and Restore the DRL

Fit the assembly into the rear housing and restore the DRL. Relieve only any actual upper interference area, then verify aim, source retention and the selected wide-voltage harness.

Selected Installation Details

06 Components to confirm

Carriers, Four Projectors and Retained-Source Wiring

Handed Main Carriers

Select the correct side and supplied clip arrangement.

Projector Sub-Brackets

Assemble all four positions as shown in the reference.

1.5–1.8-Inch Matrix Projectors

Four per lamp; verify physical fit and DRL clearance.

Retained Sources and Harness

Common-negative or independent-negative wide-voltage wiring is permitted by this source.

07 Clearance and installed result

Restore the DRL and Check Actual Upper Clearance

Restored Q4 DRL and possible local upper clearance area
Only relieve an actual upper interference area caused by the selected projector.
Installed Q4 matrix projector result
Installed reference result
08 Frequently asked questions

Q4 e-tron Matrix Retrofit FAQ

How many projectors fit each lamp?

Article 709 specifies four matrix projectors per lamp with mounting holes for 1.5–1.8-inch units. Confirm the actual selected projector dimensions and clearances.

Must the original sources remain?

Yes. The source requires retaining the original light sources. Do not remove them based on another model’s decoding solution.

Must the harness have independent negatives?

No. This article permits either common-negative or independent-negative wide-voltage harnesses. When using a common-negative H4 harness, take negative from the main vehicle connector negative, as the supplier specifies.

Where are low/high signals measured?

The supplier shows identical low- and high-beam source boards, with the same positive/negative pickup locations in the pictured orientation. Verify the actual board and connector polarity; no universal vehicle pin numbering is given.

How is the carrier assembled?

Select the correct handed carrier, fit the supplied clips and projector sub-brackets, secure four compatible matrix projectors, then fit the complete carrier into the rear housing.

What DRL clearance work is required?

Reinstall the daytime-running light. If the selected projector interferes at the upper edge, relieve only the actual affected local area shown in the source; do not assume every projector needs the same cut.

Technical reference: Supplier article 709 and supplied photographs. Verify lamp identity, four-projector fit, source polarity, harness configuration and DRL clearance.

Related Headlight Retrofit Cases

Match Your Q4 e-tron Matrix Kit

Send the original lamp and intended projector specifications.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.