01 Hero · Q2 / Q2L outer and inner conversion case

2022–2024

Audi Q2 / Q2L 81A / 81D Projector Retrofit

Outer Low-Beam Projector and Inner High-Beam Matrix Kits
INSTALLATION REFERENCE

A position-specific reference covering a flat outer projector recommendation, inner matrix mounting-base preparation and retained-source independent-negative wiring.

◇ Q2 / Q2L◇ Either Position Selectable◇ 1.5–1.8-Inch Inner Matrix

View Installation Guide

Audi Q2 Q2L vehicle front and headlamp2022–2024 Q2 / Q2L Reference
02 Vehicle application

Q2 / Q2L Position-Specific Bracket Application

Outer low beam or inner high beam can be modified separately. Match the actual 81A/81D lamp to the Q2/Q2L Xingyu reference before selecting either kit.

Models
Audi Q2 / Q2L 81A / 81D
Years
2022–2024
Headlamp
Pictured Xingyu hard-cure-sealant lamp
Layout
Outer low beam; inner 1.5–1.8-inch high-beam matrix
Factory Parts
Original sources retained; inner base locally prepared; trim restored
Q2 outer low-beam bracket pair
Separate Conversion Choices

Use outer, inner or both kits.

Flat Low-Beam Recommended

Inner matrix accepts 1.5–1.8-inch projectors.

Retained Sources

Use the specified independent-negative wide-voltage harness.

03 Position-specific kits

Different Preparation for Outer and Inner Positions

Outer low-beam carrier kit

Outer Low Beam

  • Flat projector recommended.
  • Install the carrier directly.
  • Forward-mount with the illustrated spacer post.
Inner high-beam matrix kit

Inner High-Beam Matrix

  • Fits 1.5–1.8-inch projectors.
  • Prepare the mounting base and secure the clip.
  • Take care with the difficult original clips.
04 Compatibility notice

Match the Lamp and Chosen Position

Documented Configuration

  • 2022–2024 Q2/Q2L reference
  • Separate outer and inner carrier kits
  • Inner 1.5–1.8-inch matrix projectors
  • Retained sources and independent-negative harness

Not Automatically Confirmed

  • Other lamp internals without matching
  • Source removal or common-negative wiring
  • Forcing difficult original high-beam clips
  • Using photo-relative wires without verifying orientation

Request Matching

Send lamp details and your selected conversion positions.

Request Verification

05 Installation process

Q2 Outer and Inner Installation Sequence

Open the Lamp and Remove Decorative Trim

Step 01

Open the Lamp and Remove Decorative Trim

The source identifies a Xingyu hard-cure-sealant lamp. Open the front cover and remove the decorative trim to expose the two positions.

Remove the Original Units Carefully

Step 02

Remove the Original Units Carefully

Release the original projector clips carefully. The supplier especially warns that high-beam-position clips are difficult to remove.

Prepare the Inner Mounting Base

Step 03

Prepare the Inner Mounting Base

For the inner conversion, remove the original ball stud and marked raised base, then grind the base flat as illustrated.

Secure the Inner Clip and Matrix Assembly

Step 04

Secure the Inner Clip and Matrix Assembly

Use the illustrated nut/socket method to secure the clip; a little silicone may be added at its base. Assemble and fit the 1.5–1.8-inch inner matrix carrier.

Install the Outer Low-Beam Carrier

Step 05

Install the Outer Low-Beam Carrier

For an outer conversion, fit the separate low-beam bracket directly at the documented mounting points.

Forward-Mount the Outer Projector and Restore Trim

Step 06

Forward-Mount the Outer Projector and Restore Trim

Fit the outer projector forward and add the pictured spacer post. Restore trim and verify clearance, aiming and the retained-source independent-negative harness.

Selected Installation Details

05B Mounting and source signals

Prepare the Inner Base and Verify Board Connections

Remove original ball stud and raised mounting base

Original Base Preparation

Remove only the marked raised base and grind the fixing area flat.

Nut held in socket for clip fixing

Secure the Clip

Use the illustrated nut/socket method; a little silicone may be added at the clip base.

Q2 source board low and high beam polarity references

Source-Board Reference

Low + third from left, low − first from right; high + fourth from right, high − first from left, in the pictured orientation only. Verify the actual connectors.

06 Components to confirm

Both Carriers, Clips, Projectors and Harness

Outer Low-Beam Kit

Match the carrier, hardware and pictured spacer posts.

Inner Matrix Kit

Match the carrier, clip, fasteners and prepared base.

Position-Specific Projectors

Flat outer low-beam recommended; inner 1.5–1.8-inch matrix.

Retained Sources and Harness

Use independent-negative wide-voltage wiring and verify source-board signals.

07 Assembly and result

Restore Trim after Checking Clearance

Outer projector forward mounting and spacer post
Outer forward mounting and spacer detail
Completed Audi Q2 Q2L projector retrofit
Completed reference lamp
08 Frequently asked questions

Q2 / Q2L Retrofit FAQ

Can outer and inner positions be converted independently?

Yes. Article 792 permits an outer low-beam conversion or inner high-beam conversion separately, as well as the illustrated combined 3-inch-plus-matrix arrangement.

Which projector sizes are stated?

The low-beam position is presented as a 3-inch conversion and the supplier recommends a flat projector. The inner high-beam matrix carrier fits 1.5–1.8-inch projectors.

What electrical setup is required?

Retain the original light sources and use a wide-voltage harness with independent negatives. Do not join low- and high-beam negative circuits.

What source connector references are shown?

In the pictured board orientation, low-beam positive is third from the left and negative first from the right; high-beam positive is fourth from the right and negative first from the left. These are photo-specific source-board references, not universal vehicle pin numbers.

How is the inner clip base prepared?

Remove the original ball stud, cut away the marked raised mounting base and grind it flat. Use the illustrated nut/socket arrangement to secure the replacement clip. The source permits a little silicone at the clip base.

What removal and final clearance precautions are stated?

Original clips are difficult to release, especially at the high-beam position. Work carefully, follow the inner mounting details, and install the outer projector forward with the illustrated spacer post. Verify aim, fit and clearance before completing the lamp.

Technical reference: Supplier article 792 and supplied photographs. Verify lamp identity, mounting-base preparation, difficult clip removal, source-board orientation and independent-negative wiring.

Related Headlight Retrofit Cases

Choose Your Q2 / Q2L Conversion Position

Send the original lamp and intended projector dimensions.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.