01 Hero · A7 Bosch stepper xenon case

2011–2016

Audi A7 / S7 / RS7 4G8 Xenon Bosch Stepper Retrofit

Integrated Return-Spring Carrier · Original Adaptive Motor Transfer
INSTALLATION REFERENCE

An A7 reference for the Bosch stepper system, covering side-specific motor transfer, critical swivel clearance and beam-switching-module wiring. Match each actual S7/RS7 lamp to the documented mechanism.

◇ 4G8 Xenon◇ Integrated Carrier◇ Swivel Clearance Required

View Installation Guide

Completed Audi A7 Bosch stepper projector assemblyA7 Bosch Stepper Reference Assembly
02 Vehicle application

Bosch Stepper Bracket Application

The source directly documents the A7 xenon Bosch stepper lamp. Confirm the same motor and carrier arrangement for the requested A7/S7/RS7 variants before selecting this kit.

Models
Audi A7 / S7 / RS7 4G8; A7 lamp reference
Years
2011–2016
Headlamp
Xenon Bosch stepper/adaptive mechanism
Layout
Complete replacement carrier with return spring and swivel limit
Factory Parts
Original adaptive motors transferred; lower support locally relieved
A7 Bosch stepper integrated bracket pair
Integrated Carrier Hardware

Return spring and swivel limiting parts supplied.

Original Motors Reused

Label driver and passenger sides before transfer.

Critical Swivel Clearance

Prepare the projector corner, lower support and cable space.

03 Clearance requirements

Prevent Contact throughout Adaptive Travel

Projector corner interference relief

Projector Lower-Right Corner

Maintain the illustrated cut extent so the plastic arm does not contact it.

Lower adjustment-motor support after local trimming

Lower Motor Support

Trim the marked local support area to clear swiveling.

Linkage arm attached before adaptive motor mounting

Linkage Arm First

Attach the linkage before securing the original adaptive motor.

04 Compatibility notice

Match the Actual Motor and Lamp Mechanism

Documented Configuration

  • 2011–2016 A7 xenon Bosch stepper reference
  • Integrated carrier return spring and swivel limit
  • Transferred original adaptive motors
  • Required clearance and compact cable preparation

Not Automatically Confirmed

  • Every S7/RS7 lamp based on badge alone
  • LED or unmatched non-adaptive mechanisms
  • Insufficient projector-corner or motor-support clearance
  • Reversed motor sides or unverified high-voltage cable fit

Request Matching

Send lamp labels, motor labels and original carrier photographs.

Request Verification

05 Installation process

Bosch Stepper Mechanical Installation

Prepare the Projector Corner

Step 01

Prepare the Projector Corner

Relieve the illustrated lower-right projector corner sufficiently to avoid the plastic linkage arm during swiveling. Do not reduce the documented clearance.

Mount the Projector and Preconnect the Module

Step 02

Mount the Projector and Preconnect the Module

Secure the prepared projector on the complete replacement carrier. Connect the switching-module harness before access becomes restricted.

Label and Prepare the Original Motors

Step 03

Label and Prepare the Original Motors

Keep driver/passenger motors identified. Perform only the illustrated motor preparation and remove the documented beam-switching shaft.

Attach the Linkage and Motor

Step 04

Attach the Linkage and Motor

Attach the linkage arm first, then secure the adaptive motor to the bracket with two screws.

Prepare Lower Support and Cable Clearance

Step 05

Prepare Lower Support and Cable Clearance

Remove the tall original high-voltage lead, locally trim the marked lower adjustment-motor support and use the compatible compact connector cable shown.

Fit the Assembly and Verify Swivel Travel

Step 06

Fit the Assembly and Verify Swivel Travel

Fit the projector carrier to the original rear mounts and tighten the screws. Verify linkage engagement, full swivel/height travel and cable clearance before completing the lamp.

Selected Installation Details

05B Cable and switching connections

Verify Compatibility, Signal and Polarity

Use the Compact High-Voltage Lead

Step 01

Use the Compact High-Voltage Lead

The source shows a smaller white-connector cable to clear the motor. Verify ballast/bulb compatibility; do not work on an energized high-voltage system.

Verify the High-Beam Signal

Step 02

Verify the High-Beam Signal

The photo identifies first row, second wire from the right at the pictured connector. Confirm orientation and the measured signal on the actual motor.

Connect the Switching Module

Step 03

Connect the Switching Module

Red: low-beam positive. Black: low-beam negative. Yellow: high-beam signal. Follow the actual module instructions and protect all completed connections.

06 Components to confirm

Carrier, Motors, Projector and Electrical Parts

Integrated Replacement Carrier

Includes return spring, swivel limit and bearing/bushing arrangement.

Original Adaptive Motors

Keep sides identified and transfer with the linkage arm first.

Prepared Replacement Projector

Maintain the documented corner clearance; optional small black Hella-style shroud.

Module and Compact Cable

Confirm switching-module wiring and compatible low-profile high-voltage connector.

07 Assembly and result

Check the Complete Movement Envelope

Prepared projector secured to complete replacement carrier
Projector on the integrated replacement carrier
Completed A7 adaptive projector assembly
Completed reference assembly; verify swivel and height travel.
08 Frequently asked questions

A7 Bosch Stepper Retrofit FAQ

Which lamp is documented?

Article 30 documents the 2011–2016 A7 xenon Bosch stepper arrangement. For the requested A7/S7/RS7 4G8 applications, match the actual lamp, original motor and mounting system; the badge alone does not confirm fitment.

What does the complete replacement carrier include?

The kit supplies its own return spring, swivel limit pin, bearing/bushing and retaining parts. Original adaptive motors are still transferred as shown; complete replacement refers to the carrier assembly.

Which clearance cuts are essential?

The replacement projector lower-right corner must be relieved at least to the illustrated extent to avoid the plastic linkage arm. The lower height-adjustment motor support also needs the documented local trimming to avoid swivel interference.

How are the original adaptive motors transferred?

Label driver/passenger motors before removal. Prepare them as shown, including removal of the illustrated beam-switching shaft, attach the linkage arm first and secure each motor with two screws.

Why is a different high-voltage lead shown?

The original tall ballast-to-bulb connector interferes with the adaptive motor below. The supplier replaces it with a compatible compact white-connector high-voltage cable. Verify equipment compatibility and use appropriate high-voltage precautions.

How is the beam-switching module connected?

The diagram shows red to low-beam positive, black to low-beam negative and yellow to the high-beam signal. The signal photo identifies the first row, second wire from the right on the pictured motor connector. Verify actual orientation and polarity; this is not a universal vehicle pin number.

Technical reference: Supplier article 30 and supplied photographs. Verify actual lamp/motor identity, critical cuts, adaptive travel, cable compatibility and switching-module connections.

Related Headlight Retrofit Cases

Match Your 4G8 Bosch Stepper Bracket

Send the lamp and motor labels plus original mounting photographs.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.