01 Hero · A6 non-adaptive rear-access case

2012–2017

Audi A6 C7/4G Non-Adaptive Xenon Projector Retrofit

Front Lens and Original Decorative Shroud Retained
INSTALLATION REFERENCE

A non-adaptive xenon reference using the rear service opening, with local original-carrier preparation, linkage restoration and a defined three-point installation sequence.

◇ A6 C7 / 4G◇ Non-Adaptive Lamp◇ Unmodified OEM Shroud

View Installation Guide

Original Audi A6 C7 non-adaptive xenon headlampA6 Original Shroud Retained
02 Vehicle application

A6 C7/4G Non-Adaptive Bracket Application

The supplier documents a 2012–2017 A6L non-adaptive xenon lamp with a Hella 5 projector. Rear access retains the front lens but requires local original-carrier cutting.

Models
Audi A6 C7 / 4G; A6L reference configuration
Years
2012–2017 reference range
Headlamp
Non-adaptive lamp; pictured original Hella 5 projector
Layout
Rear-access one-piece bent replacement carrier
Factory Parts
Front lens retained; original shroud, link rod and adjustment motor reused
Audi A6L non-adaptive bracket pair and clips
Original Shroud Retained

The original shroud fits the pictured replacement LED projector directly.

Rear Service Access

Local original-carrier cutting is still required.

Three-Point Engagement

Outer lower, inner lower, then upper clip.

03 Critical clip details

Follow the Three-Point Carrier Engagement Order

Outer lower mounting point first

01 Outer Lower Point

Engage the outer lower mounting point first.

Inner lower ball stud second

02 Inner Lower Ball Stud

Engage the inner lower ball stud after the outer lower point.

Upper clip installed last

03 Upper Clip Last

Install the upper clip after both lower points are engaged.

04 Compatibility notice

Verify the Non-Adaptive Mounting Arrangement

Documented Configuration

  • 2012–2017 A6L non-adaptive reference
  • Original Hella 5 projector removed through rear access
  • Replacement carrier on the original mounting arrangement
  • Unmodified decorative shroud and original adjustment motor

Not Automatically Confirmed

  • Adaptive/swiveling or unmatched lamp versions
  • Skipping the documented internal carrier preparation
  • Reversing the documented carrier engagement order
  • Unspecified wiring, decoding or harness assumptions

Request Matching

Send the lamp label, original carrier, ball studs and projector photographs.

Request Verification

05 Installation process

A6 Non-Adaptive Rear-Access Installation

Remove the Original Adjustment Motor

Step 01

Remove the Original Adjustment Motor

Work through the rear service opening. Rotate and remove the original adjustment motor as illustrated.

Release the Original Carrier Mounts

Step 02

Release the Original Carrier Mounts

Cut or drill the marked clip to release it, then follow the documented carrier-cutting and ball-stud-mount release views. Avoid unrelated structure.

Remove Projector Screws and Carrier Sections

Step 03

Remove Projector Screws and Carrier Sections

Move the original shroud aside, remove the two accessible screws, locally cut the marked plastic carrier and rotate the assembly to reach the remaining two screws.

Remove the Remaining Stud and Restore the Linkage

Step 04

Remove the Remaining Stud and Restore the Linkage

Remove the marked original plastic ball stud left in the housing. Transfer the illustrated link rod back into the rear housing and reinstall the motor.

Engage the Replacement Carrier in Order

Step 05

Engage the Replacement Carrier in Order

Seat the outer lower point first, then the inner lower ball stud and finally the upper clip. Compare all three points with the position-specific reference photographs.

Fit the Projector and Original Shroud

Step 06

Fit the Projector and Original Shroud

The pictured original shroud fits the replacement LED projector directly. Insert and secure the projector, then check mounting, centering and adjustment.

Selected Installation Details

06 Components to confirm

Carrier, Clips, Projector and Original Parts

One-Piece Bent Carrier

Match the non-adaptive xenon bracket pair and clip orientation.

Three Mounting Points

Confirm the outer lower point, inner lower ball stud and upper clip.

Replacement Projector and OEM Shroud

Match the selected projector to the pictured direct-fit shroud reference.

Original Link Rod and Motor

Transfer the link rod and restore the original adjustment motor.

07 Centering and result

Maintain the Original Shroud Clearance

A6 C7 replacement projector front detail
Centering and clearance reference with the original decorative shroud
Completed A6 C7 non-adaptive retrofit
Completed front fit with the original shroud on the pictured projector
08 Frequently asked questions

A6 C7 Non-Adaptive Retrofit FAQ

Which original lamp is documented?

Article 103 covers the 2012–2017 A6L non-adaptive xenon lamp with an original Hella 5 projector. Match the actual A6 C7/4G lamp and internal mounting arrangement.

How can the front lens remain closed?

The supplier uses the relatively large rear service opening. Internal plastic-carrier cutting and mount release are still required; this is not an unmodified drop-in replacement.

What must be removed from the original carrier?

Release all three original plastic-carrier mounts, move the original shroud aside, remove the accessible projector screws and locally cut the illustrated carrier sections to reach the remaining screws.

What happens to the remaining ball stud and link rod?

Remove the original plastic ball stud remaining in the housing at the marked position. Transfer the illustrated link rod back into the rear housing and restore the original adjustment motor.

What is the replacement carrier installation order?

Engage the outer lower mounting point first, then the inner lower ball stud, and install the upper clip last. Follow the separate photographs for all three points.

Can the original decorative shroud be used?

The supplier shows the original decorative shroud fitting directly onto the pictured replacement LED projector. Verify the selected projector and actual centering/clearance. No universal wiring pinout or decoding requirement is provided.

Technical reference: Supplier article 103 and supplied installation photographs. Verify lamp identity, carrier preparation, linkage restoration, mounting order and adjustment before installation.

Related Headlight Retrofit Cases

09 Business inquiry

Match Your A6 Non-Adaptive Bracket

Send the lamp label and original projector, carrier and mounting-point photographs.

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.