01 Hero · A3 facelift high-spec LED case

2017–2020

Audi A3 8V Facelift High-Spec LED Projector Retrofit

One-Piece Bent Metal Projector Bracket
INSTALLATION REFERENCE

A Valeo LED-lamp reference covering trim release, carrier fitting, original-source restoration and separately documented low/high-beam signal connections.

◇ A3 8V Facelift◇ High-Spec LED◇ Original LED Source Restored

View Installation Guide

Original Audi A3 facelift high-spec Valeo LED headlampA3 High-Spec LED Reference Lamp
02 Vehicle application

A3 High-Spec LED Bracket Application

Match the Valeo LED headlamp and internal arrangement shown. This procedure opens the front cover and does not use the xenon rear-housing cut method.

Models
Audi A3 8V Facelift
Years
2017–2020 reference range
Headlamp
High-spec LED; pictured Valeo hard-cure-sealant lamp
Layout
Replacement metal projector carrier
Factory Parts
Original LED source restored; light guide and trim refitted
Audi A3 high-spec LED bracket pair blocking plates and hardware
One-Piece Bent Bracket

Match the supplied carrier and clip arrangement.

Original LED Source

Refit below the low-beam projector with the blocking plate.

Separate Signal Checks

Confirm the low-beam harness and 9–10 V high-beam signal.

03 Technical details

Carrier, Shroud and Original Source Preparation

One-piece bent metal carrier without welded construction

Bent Metal Carrier

The supplier illustrates a one-piece bent construction without welding.

A-type projector shroud recommended

A-Type Shroud

The source recommends this shroud style; check fit with the actual replacement projector.

Original high-beam LED source removed for restoration

Original LED Source

Remove the source from the original assembly for blocking-plate installation and documented refitting.

04 Compatibility notice

Confirm the High-Spec LED Configuration

Documented Configuration

  • 2017–2020 A3 8V facelift high-spec LED application
  • Pictured Valeo hard-cure-sealant lamp
  • Metal carrier and A-type shroud reference
  • Original LED source restored below the projector

Not Automatically Confirmed

  • Xenon rear-access or halogen lamp procedures
  • Unmatched lamp manufacturers or internal layouts
  • Unverified connector orientation or terminal numbering
  • Assuming the 9–10 V signal is a normal 12 V supply

Request Matching

Send the lamp label, original carrier and LED-source connector photographs.

Request Verification

05 Installation process

High-Spec LED Mechanical Installation

Open the Lamp and Release the Trim

Step 01

Open the Lamp and Release the Trim

The reference is a Valeo hard-cure-sealant lamp. Open the front cover and release the marked outer decorative-trim clips.

Remove the Trim and Light Guide

Step 02

Remove the Trim and Light Guide

Release the inner-edge and clear-trim clips. Remove the front and lower trim; lift the light-guide retaining barbs as illustrated.

Release the Original Carrier and Link Rod

Step 03

Release the Original Carrier and Link Rod

Warm the original clip area before release. Remove the projector bracket and the ball-joint link rod without forcing the surrounding parts.

Install the Metal Bracket

Step 04

Install the Metal Bracket

Fit the replacement carrier directly at the documented mounting points, matching the supplied clip and bracket arrangement.

Secure the Projector and Shroud

Step 05

Secure the Projector and Shroud

Fasten the replacement projector. The source recommends an A-type shroud; confirm local fit and clearance.

Restore the Original Source and Trim

Step 06

Restore the Original Source and Trim

Fit the light-blocking plate and prepare the heat-sink clearance as shown, then reinstall the original LED source below the low-beam projector. Restore the light guide and trim and verify operation.

Selected Installation Details

05B Source and signal details

Original Source Restoration and Beam Connections

Fit the Light-Blocking Plate

Step 01

Fit the Light-Blocking Plate

Secure the supplied plate directly. Trim the heat sink locally on both front and rear sides at the illustrated areas.

Confirm the Low-Beam Signal

Step 02

Confirm the Low-Beam Signal

The source marks the second wire from the left as low-beam positive in this photo orientation. Use the low-beam harness and verify the actual connector.

Verify High-Beam Switching

Step 03

Verify High-Beam Switching

The high-beam positive signal is shown as approximately 9–10 V. The optional module uses red supply positive, black negative and yellow signal, with two switching outputs; confirm the actual module ratings and connections.

High-beam positive signal location approximately 9 to 10 volts
High-beam signal location with the original reflector left in place; verify on the actual lamp.
06 Components to confirm

Carrier, Projector, Blocking Plate and Harness

One-Piece Bent Carrier

Match the carrier pair and supplied mounting hardware; the source shows a bent construction without welding.

Projector and A-Type Shroud

Confirm projector fixing points and the recommended A-type shroud fit.

Original Source and Blocking Plate

Restore the original LED source below the low-beam projector after the documented heat-sink preparation.

Harness and Switching Option

Verify the low-beam harness and optional high-beam switching module against the measured signal.

07 Front fit and result

Restore the Light Guide and Decorative Trim

Audi A3 high-spec LED replacement projector front close-up
Replacement projector front detail
Completed Audi A3 high-spec LED projector retrofit
Completed high-spec LED reference lamp
08 Frequently asked questions

A3 High-Spec LED Retrofit FAQ

Which headlamp is documented?

The supplier documents the 2017–2020 A3 high-spec LED application using the pictured Valeo lamp with hard-cure sealant. This is separate from the xenon rear-access procedure.

Does the front lens remain closed?

No. The LED sequence shows the front cover opened so that the decorative trim, light guide and original projector carrier can be removed.

What shroud is recommended?

The installation photograph recommends an A-type projector shroud. Verify actual clearance with the chosen projector.

What happens to the original LED source?

Remove the original high-beam LED source from the assembly, fit the supplied light-blocking plate, locally trim the heat sink at the illustrated front and rear areas and reinstall the original source below the low-beam projector.

Which low-beam connection is identified?

The photo identifies the low-beam positive signal as the second wire from the left in the pictured orientation. The article states that a harness is used for low beam; verify the actual connector orientation and electrical requirements.

How is the high-beam signal handled?

The photo identifies a high-beam positive signal of approximately 9–10 V without removing the reflector. An optional beam-switching module is shown: red to projector supply positive, black to negative and yellow to the identified high-beam signal, with two switching outputs. Confirm compatibility rather than treating the signal as a normal 12 V supply.

Technical reference: Supplier article 165 and supplied installation photographs. Verify lamp identity, original-source mounting, measured beam signals and module compatibility before installation.

Related Headlight Retrofit Cases

09 Business inquiry

Match Your A3 High-Spec LED Bracket

Send the lamp label, internal layout and source connector photographs.

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.