Audi A3 8V Xenon Projector Retrofit
A Pre-Facelift xenon-lamp reference covering rear access, careful original-carrier removal, metal bracket fitting and rear-housing waterproof restoration.
A3 8V Xenon HeadlampA3 8V Rear-Access Bracket Application
The front lens remains in place, but the rear housing must be cut and subsequently restored. Match the original Hella lamp, projector and plastic carrier to the pictured configuration.
- Models
- Audi A3 8V Pre-Facelift
- Years
- 2014–2016 reference range
- Headlamp
- Xenon Hella lamp; original Hella 6 projector
- Layout
- Metal replacement bracket through a rear access cut
- Factory Parts
- Front lens retained; leveling motor restored; rear housing repaired

Rear-housing cutting is still required.
Protect the original plastic support and fragile ball joint.
Refit, plastic-weld and seal the rear panel as documented.
Rear Access and Fragile Original Mounts
Do Not Reverse the Clips
Match each clip orientation to the supplied bracket photograph.
Fragile Ball Joint
The source warns that this joint breaks easily. Use the illustrated side access rather than forcing the plastic assembly.
Restore the Cut-Out Panel
Rear access must be closed with the documented plastic-welding, sealing and waterproofing work.
Confirm the Xenon Lamp Before Disassembly
Documented Configuration
- Pictured 2014–2016 A3 8V Pre-Facelift xenon lamp
- Original Hella 6 projector and plastic carrier
- Rear access with the front lens retained
- Replacement metal bracket and restored leveling motor
Not Automatically Confirmed
- Halogen, LED or other lamp versions
- A modification without rear-housing cutting
- Undocumented wiring pinouts or decoding claims
- Unsealed or unsupported rear-housing repairs
Request Matching
Send the lamp label, rear housing and original projector/carrier photographs.
A3 Xenon Rear-Access Installation Sequence
Create the Rear Access Opening
Retain the front lens. The supplier illustrates warming and cutting only the outlined rear-housing section; preserve the cut-out piece for restoration.
Release the Reflector and Switching Motor
Carefully release the two reflector clips, rotate the reflector counterclockwise and remove it. Then remove the illustrated beam-switching motor.
Release the Original Plastic Carrier
Follow the marked local cutting and clip-release views. Work carefully around the fragile ball joint; do not force the original plastic support.
Restore the Leveling Motor and Fit the Carrier
Reinstall the headlamp leveling motor and fit the metal bracket. Install the supplied clips in the illustrated orientation without reversing them.
Insert and Secure the Replacement Projector
Fit the projector directly through the rear access and secure the mounting screws. The optional small black Hella-style shroud is shown for appearance.
Restore and Waterproof the Rear Housing
Refit the cut-out housing section. The supplier calls for plastic welding, sealant and waterproof restoration. Check mounting, leveling and lamp operation before service.
Selected Installation Details
Bracket, Projector, Leveling Parts and Rear Panel
Metal Bracket and Clips
Match the carrier pair and clip orientation to the reference photographs.
Replacement Projector
Check the projector mounting and optional small black Hella-style shroud.
Original Leveling Parts
Restore the leveling motor and handle the original ball joint and clips carefully.
Rear-Housing Restoration
Retain the cut-out panel and prepare the plastic-welding and waterproof sealing solution.
Front Lens Remains in Place


A3 8V Xenon Retrofit FAQ
Does no front-lens opening mean no cutting?
No. This documented method retains the front lens but requires cutting a marked section of the rear housing. The removed section must be restored, plastic-welded, sealed and waterproofed.
Which original lamp is described?
The supplier describes the pictured 2014–2016 Audi A3 xenon lamp as a Hella headlamp with cold/hard sealant and an original Hella 6 projector. Verify the actual lamp label and internals.
What needs particular care during removal?
The original plastic-carrier clips require careful release. The marked ball joint breaks easily; the photos show side access with a flat-blade screwdriver if the original joint breaks.
How is the original reflector removed?
Release the two marked reflector clips, then rotate the reflector counterclockwise. Remove the beam-switching motor as illustrated before continuing the carrier disassembly.
Is an optional shroud shown?
Yes. The supplier shows a small black Hella-style shroud as an optional appearance detail. Check its actual fit with the selected replacement projector.
Is a wiring pinout or decoding requirement provided?
Article 93 does not specify vehicle pin numbers or a decoder requirement. Confirm the electrical arrangement for the actual replacement projector rather than assuming a universal connection.
Technical reference: Supplier article 93 and supplied installation photographs. Verify lamp identity, original mounts, replacement fit and rear-housing waterproof restoration before installation.
Related Headlight Retrofit Cases
Match Your Audi A3 Xenon Bracket
Send the lamp label, rear housing, original carrier and replacement projector details.






















