01 Hero · A1 8X facelift xenon case

2015–2017

Audi A1 8X Factory-Xenon Projector Retrofit

Facelift Replacement Projector Bracket
INSTALLATION REFERENCE

A factory-xenon reference covering front-cover access, hidden upper trim screw removal, tight-fit motor transfer and forward-mounted replacement projector installation.

◇ A1 8X Facelift◇ Factory Xenon◇ ZKW Reference Lamp

View Installation Guide

Audi A1 8X vehicle front and xenon headlampA1 Factory-Xenon Reference
02 Vehicle application

A1 8X Xenon Bracket Application

The supplier states that a conventional compatible projector can use the original supply without decoding in this factory-xenon reference. Verify the actual lamp and selected projector rather than extending this to other versions.

Models
Audi A1 8X Facelift
Years
2015–2017
Headlamp
High-spec factory xenon; pictured ZKW hard-cure-sealant lamp
Layout
Forward-mounted projector on replacement metal carrier
Factory Parts
Adjustment motor transferred; original supply and decorative trim restored
Audi A1 facelift xenon bracket pair and clips
Clip and Motor Assembly

Match clip orientation and the upward-facing motor connector.

Forward Projector Mounting

Fit the projector on the carrier before housing installation.

Supplier Electrical Note

No decoding is specified for this documented factory-xenon configuration.

03 Compatibility notice

Confirm the Factory-Xenon Lamp

Documented Configuration

  • 2015–2017 A1 facelift factory xenon
  • Pictured ZKW lamp and original mounting points
  • Supplied clip assembly and metal carrier
  • Compatible projector on the original supply

Not Automatically Confirmed

  • Halogen or unmatched lamp versions
  • Decoder-free operation for every projector
  • Guessed connector pins or polarity
  • Unspecified additional harness/module assumptions

Request Matching

Send the lamp label and selected projector specifications.

Request Verification

04 Installation process

A1 Xenon Projector Installation

Open the Front Lens Cover

Step 01

Open the Front Lens Cover

Verify the ZKW factory-xenon reference lamp and use an opening procedure suitable for its hard-cure sealant.

Remove the Hidden Upper Screw

Step 02

Remove the Hidden Upper Screw

Remove the marked hidden upper screw before trying to release the complete decorative trim.

Remove the Decorative Trim and Original Unit

Step 03

Remove the Decorative Trim and Original Unit

Release the complete trim after the screw is removed, then remove the original projector assembly and retain the documented adjustment motor.

Install the Motor with Connector Upward

Step 04

Install the Motor with Connector Upward

Assemble the accessory clips. Warm the tight-fitting motor sealing ring before fitting the motor, and check that its final connector orientation is upward.

Forward-Mount the Projector

Step 05

Forward-Mount the Projector

Secure the compatible replacement projector in the illustrated forward position on the assembled carrier.

Install the Carrier and Restore Trim

Step 06

Install the Carrier and Restore Trim

Fit the bracket assembly in the rear housing. Restore trim, check adjustment and clearance, and verify the compatible original factory-xenon supply connection.

Selected Installation Details

05 Components to confirm

Carrier, Clips, Projector and Original Parts

Metal Carrier Pair

Match the 2015–2017 facelift xenon bracket and hardware.

Clips and Adjustment Motor

Warm the motor sealing ring and fit the connector upward.

Compatible Replacement Projector

Fit in the forward position and verify actual clearance.

Original Supply and Trim

Verify electrical compatibility and restore the original trim.

06 Assembly and result

Restore the Original Decorative Trim

A1 facelift replacement projector front detail
Replacement projector with original trim restored
Completed A1 facelift factory-xenon projector retrofit
Completed reference headlamp
07 Frequently asked questions

A1 8X Factory-Xenon Retrofit FAQ

Which configuration is covered?

Article 1496 documents the 2015–2017 Audi A1 factory-xenon lamp. The photographs identify a ZKW lamp with hard-cure sealant. Match the actual 8X facelift lamp and carrier.

What must be removed before the complete trim?

Remove the hidden upper screw shown in the close-up before releasing the complete decorative trim. Do not force the trim with the screw still installed.

How is the adjustment motor fitted?

The motor is a tight fit. The source says to warm the motor sealing ring with a heat gun before installation, with the final motor connector facing upward.

How is the projector mounted?

Assemble the supplied accessory clips and transferred motor on the carrier, fit the replacement projector in the forward position, then install the complete bracket in the housing.

Is decoding required?

The supplier states that the documented original factory-xenon configuration does not require decoding and a conventional compatible projector can use the original supply. Verify actual equipment compatibility; this is not a rule for all A1 lamp versions.

Are extra harnesses or universal pin numbers specified?

No. This article does not provide universal pin numbers or specify a separate wide-voltage harness or switching module. Verify actual polarity and compatibility rather than copying another case.

Technical reference: Supplier article 1496 and supplied photographs. Verify factory-xenon lamp identity, clip assembly, projector fit and original-supply electrical compatibility.

Related Headlight Retrofit Cases

Match Your A1 Factory-Xenon Bracket

Send the original lamp and intended projector photographs.

Request This SolutionContact Royalin

REQUEST A BUSINESS SOLUTION

For retrofit shops, distributors and automotive lighting businesses.

We supply automotive lighting retrofit solutions and components exclusively for business customers worldwide.

1. Your Business
2. Your Vehicle
3. Contact Information
4. Your Message (Optional)

We will reply within 1 business day.